Installation Instructions for Peg Perego
®
Primo Viaggio
®
The Double Snap-N-Go
®
will accommodate the Peg Perego
®
Primo Viaggio
®
Infant Car Seat. Please follow these instructions for proper installation of the
Primo Viaggio
®
.
Front Seat:
1. Remove (unscrew) Crossbars A1, B1, and D from the Double Snap-N-Go
®
frame. Remove the Car Seat Straps from the Double Snap-N-Go
®
frame.
Retain the screws you remove.
2. Attach Crossbar A1 to the Double Snap-N-Go
®
frame using the two holes
labeled #4. Use the two screws that you removed in step 1. Please see
figure 1.
3. Attach both Car Seat Straps to the Double Snap-N-Go
®
frame using the two
holes labeled #3. Use the two screws that you removed in step 1. Please
see figure 1.
Rear Seat:
1. Remove (unscrew) Crossbars A2, B2, and B1 from the Double Snap-N-
Go
®
frame. Remove the Car Seat Straps from the Double Snap-N-Go
®
frame. Retain the screws you remove.
2. Attach Crossbar A2 to the Double Snap-N-Go
®
frame using the two holes
labeled #3. Use the two screws that you removed in step 1. Please see
figure 2.
3. Attach Crossbar B1, so that the bent section faces down, to the Double
Snap-N-Go
®
frame using the two holes labeled #4. Use the two screws that
you removed in step 1. Please see figure 2
4. Attach both Car Seat Straps to the Double Snap-N-Go
®
frame using the two
holes labeled #2. Use the two screws that you removed in step 1. Please
see figure 2.
Insertion of the Peg Perego
®
Primo Viaggio
®
Infant Car Seat:
1. With one hand grasp the car seat handle (in its upright, carrying position)
and with your other hand squeeze the handle on the back of the car seat
(see step 8, to remove car seat, of the Primo Viaggo instructions) and gently
place the seat, so that the baby faces the rear, onto the Double Snap-N-Go
®
so that the rear small grooves on the seat bottom hook over Crossbar C for
the front or Crossbar B1 for the rear. Release the handle and check that the
seat locked onto the bar. See Figure 3.
FOR SAFE OPERATION, IT IS
VERY IMPORTANT THAT THE REAR LATCHES OF THE SEAT
LOCK SECURELY ONTO THE CROSSBAR.
2. Feed the Car Seat Straps through the two slots found on the rear of the Peg
Perego
®
Primo Viaggio
®
Car Seat shell as shown in figure 4. Buckle the
two straps together. The first time your do this, you will need to adjust the
length of the strap for a tight fit around the car seat. Please see figure 4.
3. Test for secure installation by moving the car seat in all directions. The car
seat should be securely attached to the Double Snap-N-Go
®
.
Removal of the Peg Perego
®
Primo Viaggio Infant Car Seat
1. Unlock the Car Seat Strap and remove.
2. With one hand, grasp the car seat handle (in its upright, carrying position)
and with your other hand squeeze the handle on the back of the car seat (see
step 8, to remove car seat, of the Primo Viaggo
®
instructions) and lift the car
seat upward from the Double Snap-N-Go
®
. See Figure 5.
Bar A1
Hole #5
Hole #4
Hole #3
Strap
Bar C
Bar A2
Bar B1
down
Hole #3
Hole #2
Strap
Hole #4
13
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Peg Perego
®
and Primo Viaggio
®
are the trademarks of their owners. They
are not associated with Baby Trend and no approval or endorsement is implied.
