background image

8. Trouble Shooting 

7. Adjustment of thread take-up 

 

 

7-1 NEEDLE THREADS ARE UN BALANCED ;  

  

 * Is the  BLCS threaded correctly? 

 See Instruction Book P.14,15. 

  

 * Are the threads snapped in the head guide? 

 See Instruction Book P.15. 

  

 * Are the threads recommended high quality?  

 See Instruction Book P.7 . 

 

7-2 LOOPER THREADS ARE UNBALANC ED ; 

  

 * Is the  BLCS threaded correctly?  

 See Instruction Book P.14,15. 

  

 * Are the threads snapped in the head guide? 

 See Instruction Book P.15.

  

 * Are the threads recommended high quality?  

 See Instruction Book P.7. 

 

  7-3 THREAD BREAKS ; 

  

 * Is the  BLCS threaded correctly?  

 See Instruction Book P.14,15. 

  

 * Are the threads snapped in the head guide? 

 See Instruction Book P.15. 

  

 * Are the threads recommended high quality?  

 See Instruction Book P.7. 

 

 

  7-4 JET AIR THREADER DOES NOT WORK 

     *Is air deflated from pump?

  

See P.13. 

 

     *Are pipes connected properly?  

 See P.13. 

 

     *Are there any lints or thread in pipes?  

 

 

 

 

 

 

 

   

 

 

 

 

 

 

7

BLCS3

Correct Position
(Thread take-up is 
lowest position.)

CORRECT POSITION: When thread take-up is lowest position, thread take-up and 
thread guide are same position. See illustration below.

a). Rotate the machine pully and bring thread take-up at the lowest position.
b). Loosen thread take-up height position adjusting screws.
c). Adjust the thread take-up to correct position. See illustration below.
d). Tighten the fixing screws.

Thread take-up
height position 
adjusting screws

 

Содержание Model BLCS









Отзывы: