background image

5. ADJUSTMENT OF NEEDLE THREADER

(see P12)

Before you adjust the needle threader, you are required to exchange the new needles of 
SCHMETZ HAX1SP #11CR

   as the bent needles or different needles cause the incorrect timing of 

needle threader.  Also, you are required to make sure that needles are positioned in the needle
clamp holder correctly.

5-1 REPLACEMENT OF NEEDLE THREADER

a) Remove the needle threader hook fixing screw      and replace the hook    . 
b) Insert the hook     until the end of needle threader selector plate      and tighten the needle

threader hook fixing screw     . 

c) Change the needle threader select plate      right and left, and make sure if the needle threader

works both for right and left needles. 

5-2 ADJUSTMENT OF HIGH AND LOW DIRECTION FOR NEEDLE THREADER

a) Align the green marks on the pulley.
b) Make sure that the needle threader hook      is positioned until the end of needle threader 

select plate     . 

c) Bend the place A on needle threader holder     and adjust the direction of high and low for the 

needle threader

d) Change the needle threader select plate     right and left, and make sure if the needle threader 

works both for right and left needles. 

5-3 ADJUSTMENT OF RIGHT AND LEFT DIRECTION FOR NEEDLE THREADER

a) Align the green marks on the pulley.
b) Loosen the screw     and move the needle threader holder       right and left until the needle 

threader works properly. 

c) Tighten the screw     . 
d) Change the needle threader select plate     right and left, and make sure if the needle threader

works both for right and left needles. 

3-4 ADJUSTMENT OF NEEDLE THREADER SAFETY PLA TE

a) Align the green marks on the pulley.
b) Loosen the screw     and adjust the position of washer    in order to make the needle threader

safety plate lowered smoothly when the needle threader lever     is lowered.

c) Tighten the screw     . 
d) Rotate the machine pulley and make sure that the needle threader lever     is not lowered

when the needles are not in the highest position.

11

19

17

17

25

25

25

25

25

19

17

20

21

21

20

9

9

11

14

14

Содержание BLE1 AT

















Отзывы: