3
2
Feeding Porridge:
FILL LINE
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Using the Potty:
Crying:
Fig. 9
Fig. 10
1. Move the switch under the cake from OFF to ON (Fig. 11).
2. Press the button to turn on the light. Blow into the small opening on the cake to extinguish the light (Fig. 12).
Cake:
Fig. 11
Fig. 12
It is absolutely necessary to clean the internal tube system immediately after emptying. See CLEANING.
BATTERY REPLACEMENT:
An adult must install fresh alkaline batteries in your cake should the
batteries need replacing. Here’s how:
1. Using a Phillips screwdriver (not included), remove the
screw and battery compartment cover located under the cake.
2. Install three (3) fresh 1.5V AG13 (LR44) alkaline batteries (not
included) making sure the (+) and (-) ends face the proper
direction as indicated inside the battery compartment.
3. Replace the compartment cover and tighten the screw.
Cleaning:
1. If the doll gets dirty, wipe with a damp cloth and mild dish soap.
External:
Internal:
1. After feeding and bathing, fill the bottle with warm water and mild dish soap.
2. Insert the tip of the bottle halfway into the baby’s mouth pointing downward and squeeze the bottle.
NOTE: Inserting the bottle too far will clean the wrong internal tubing.
3. Once the bottle is empty, shake the baby to loosen the remnants inside.
4. Place the doll on the potty in sitting position and press and hold the belly button to fully empty out the doll.
5. Repeat as necessary. Then, rinse out the doll twice with clear water only.
6. Leave the doll on the potty for at least 15 minutes to ensure she is completely empty.
Your doll can have a bath in the bathtub or be taken to the
swimming pool, but do not fully immerse in water (Fig 13).
• For bathing, only use cold or lukewarm water and only use
common bath additives suitable for children.
• The doll should not be left in the bath, chlorine water or salt
water for more than 1 hour as color deterioration or
bleaching may occur. After bathing, clean the doll with
fresh water.
bathtub sold separately
Fig. 13
Drying:
Fig. 14
Fig. 15
Fig. 16
An ADULT must clean the doll.
IMPORTANT: After cleaning with soapy water, repeat the process with a vinegar and water solution.
Mix a small amount of regular vinegar with warm water. Then, repeat the cleaning process above.
Finally, repeat the cleaning process with clear water at least twice.
Bathing:
WARNING: Constant, competent adult supervision is REQUIRED when children are playing around water.
WARNING: THIS DOLL IS NOT TO BE USED AS A FLOTATION DEVICE.
• DO NOT allow children to play in water that is near an electrical source or apparatus.
• DO NOT leave the doll near an electrical source or apparatus when wet.
• NEVER use any of the included accessories with a real baby!
• NEVER shake a real baby!
• Please follow all instructions in this manual when playing with the doll in water.
• Be sure to clean the doll after going in the water.
• DO NOT place the doll in extremely hot or extremely cold water.
SAFETY INSTRUCTIONS
1. Fill the plate up to the mark (12 ml) with water (Fig. 5).
2. Mix in the food packet until all lumps are stirred in and the water has been fully absorbed.
The mixture will have a thin consistency.
3. Sit him upright, but tilt him back at an angle. Support him with your arm, and feed him with your other hand
using the included spoon (Fig. 6).
NOTE: If porridge comes out of the doll’s mouth when feeding, empty the doll by pressing the belly button.
Then, try feeding the doll again.
1. Undress the doll, bend his legs, and place him on the potty in the sitting position (Fig. 7).
2. Grip and hold the doll’s belly button with both hands, press down hard, and hold the pressure to make the doll go potty. Keep
the belly button pressed until the doll is completely empty (Fig. 8).
1. After feeding with water, grasp the doll with both hands under his arms and press the middle of his chest several times using
your fingers or thumbs. He will cry (Figs. 9-10)!
NOTE: If there aren’t enough tears, feed him more water.
1. Place the doll on his back and move his arms to a vertical position above his head.
2. Press his arms several times to remove any water from his arms. Repeat as needed (Fig 12).
3. Position the doll upright. If there is water in the body, it will leak out of the two holes in the doll’s body (Fig. 13). If there is water
in his legs, it will leak out of the two holes in the doll’s feet (Fig. 14).
4. Shake the doll to hear any remaining water in the doll’s body, and repeat these steps until all water is removed from the doll.
5. Dry the doll and all the joints with a towel. Let the doll air dry in a well-ventilated area until completely dry.
OFF
ON
3 x 1.5V
AG13 (LR44) Batteries
