B.Pro TS-H1 Скачать руководство пользователя страница 33

Страница: 33 / 52

Mobile Plate Dispenser

OPERATING INSTRUCTIONS

Troubleshooting

Cause

Measure

Mains plug is unplugged.

Connect the mains plug to the socket outlet.

Mains cable is damaged; e.g. a wire is
broken (can also occur without external
damage).

Have a centre authorised to carry out repairs
replace the mains cable.

Chapter "Repairs"

Customer-supplied fuse (building fuse) is
defective.

Check customer-supplied fuse and replace if
necessary.

Unit electrical system is defective.

Notify a centre authorised to carry out repairs.

Chapter "Repairs"

Cause

Measure

Temperature setting set too low.

Set a higher temperature.

Chapter "Setting the setpoint temperature"

Unit not covered with hooded cover.

Cover unit with hooded cover.

Unit electrical system is defective.

Notify a centre authorised to carry out repairs.

Chapter "Repairs"

Cause

Measure

Overload protection has been triggered.

Notify a centre authorised to carry out repairs.

Chapter "Repairs"

Unit electrical system is defective.

Notify a centre authorised to carry out repairs.

Chapter "Repairs"

Cause

Measure

Temperature control is defective.

Notify a centre authorised to carry out repairs.

Chapter "Repairs"

Cause

Measure

Guide rods not set correctly.

Adapt guide rods to the plate diameter.

Section "Adjusting guide rods to the plate dia-
meter"

Plate size is not suitable for the stacking
unit.

None.

Operation indicator does

not illuminate

Operation indicator

lit, but dishes are not

heated/kept warm

sufficiently

Operation indicator lit,

but unit interior remains

cold

The unit always heats

at the maximum

temperature, regardless

of the control setting

Plates are too large or

small for the stacking

well

Содержание TS-H1





















































Результаты поиска

Содержание TS-H1

Отзывы:

Похожие инструкции для TS-H1

Бренды по названию

Популярные бренды

B.Pro TS-H1, Перевод оригинальной инструкции по эксплуатации

Результаты поиска

Содержание TS-H1

Отзывы:

Похожие инструкции для TS-H1

Бренды по названию

Популярные бренды