RELEASE DATE
11/02/2021
REFERENCE NUMBER
INS000933
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
5/64” Allen Wrench
Waterproof Wire Connectors
Please refer to the low
voltage design guide at www.
bklighting.com/lvguide before
installation for proper wire
selection.
TOOLS
NEEDED:
Warning
Low Voltage
Hot Surface
· Suitable for wet locations · Suitable for in ground installations
IMPORTANT LISTINGS AND CERTIFICATIONS
Dia.
(56mm)
(32mm)
1 1/4"
(191mm)
7 1/2"
2 1/4"
8 3/4"
(222mm)
(42mm)
1 5/8" Dia.
(56mm)
8 3/4"
(222mm)
(32mm)
1 1/4"
Dia.
2 1/4"
7 1/2"
(191mm)
(42mm)
1 5/8" Dia.
6" Dia.
(152mm)
2 1/4" Dia.
(57mm)
1 1/2" O.C.
(38mm)
7/8"
(152mm)
(22mm)
Concrete
Pour Collar
5’
(1524mm)
18 Ga.
2 low voltage
direct burial
cable
PVC Housing
Body
Faceplate
18 Ga. Wire
Flush Mount
Collar
Flammable
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.
• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL
SAFETY AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.
• Replace LED assembly only with correct wattage and type
of power supply appropriate for LED assembly.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause
an unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY
TO PERSONS IMPORTANT
SAFETY INSTRUCTIONS
Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time.
Use a soft cloth or gloves. Oil from skin may cause
damage.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION
INSTRUCTIONS
Flush Mount Installation
MINI-MICRO RECESSED UPLIGHT
