Activation of light for 12 h via mains interruption
1. Interrupt current of both supply lines
2. Apply current for 2 to 5 sec.
3. Interrupt current again
4. Apply current
5. Detector is now ON for 12 h
Exiting sabotage
1. Interrupt current of both supply lines
2. Apply current for 30 to 60 sec.
3. Interrupt current again
4. Apply current
5. Detector is in simple closed state
15. Other functions
16. Fully automatic and semi automatic mode
(see functions IR-PD-1C)
Fully automatic operation
In this operating mode, the lighting switches automatically
on and off for increased comfort, depending on presence
and brightness.
- Channel 1 switches on in the event of motion if “dark“ is
detected.
Semi automatic operation
In this operating condition, in order to gain increased
savings, the lighting is energized only after being
manually switched on.
Switch-off takes place automatically or manually.
The semi automatic mode basically behaves like the fully
automatic one. However, the difference is that switching-on
must always be carried out manually!
As many (closer-contact) buttons as desired can be wired
in parallel on the “S” button input (ON/OFF).
Triggering in semi automatic mode:
If the detector switches
off in semi automatic mode (lag timer elapsed), the detec-
tor is switched on again within 10 sec. by motion (despite
semi automatic mode).
HA
ON/OFF
In case the sensing area of the
LUXOMAT
®
PD4-M-2C-DS
is too large or areas are being covered that should not be
monitored, the range can be reduced or limited through use of
the enclosed masking clips.
18. Exclude sources of interferences
Type
FC
PD4-M-2C-DS (Master and Slave)
92760
LUXOMAT
®
Remote control
:
IR-PD-1C (incl. wall bracket)
92520
Accessory:
BSK Ball basket guard 92199
Wall bracket for remote control as
replacement
92100
19. Article / Part nr. / Accessory
Sensor and power supply in one case
Power supply:
230 V~ ±10 %
Buffering period of tension:
200 ms
Power consumption:
< 1W
Ambient temperature:
-25°C to +50 °C
Degree of protection/class:
IP20 / II
BUS and pushbutton connections:
screened cable: 0.28 mm
2
maximum cord length: 30 m
Settings:
Potentiometer, DIP-switch and by remote control
Light values:
20-1000 Lux by remote control
10-2000 Lux by potentiometer
Extension of the detection area:
with max. one device in slave-
configuration
Area of coverage:
circular 360°
Range of coverage Ø H 2,50 m / T = 18°C:
seated 6,40 m / tangential 24 m / radial 8 m
Recommended height for mounting:
2 - 3 m
Light measurement:
da artificial light
• Power switch for light (both circuits)
Type of contact
: NOC/with pretravel tungsten contact
Contact load:
2300 W cos
ϕ
=1 /
1150 VA cos
ϕ
= 0.5, µ-Contact
Time-settings:
15 sec. - 60 min./ test with potentiometer
5 min. - 30 min./ test with remote control
Dimension:
PD4-M-2C-DS-DE H 100 x Ø 117 mm
Visible portion when built into ceiling FC:
H 37 x Ø 117mm
Declaration of Conformity:
The product complies with
the low voltage recommendation 2006/95/EC and the EMV
recommendation 2004/108/EC.
20. Technical data PD4-M-2C-DS
17. Range of Coverage
walking towards
walking across
seated
1
2
3
24 m
8 m
6,40 m
24 m
360°
2,50 m
2
3
1
21. Wiring diagram
Standard mode with master (2 alternating current circuits) and
pushbutton as well as one device in slave-configuration
Optional
PB1/2 = optional sensing device;
Slave = PD4-M-2C-DS in slave configuration
PD4-M-2C-DS
L1
N1
L2
N2
PE
N2 L2 L2‘
L1‘ L1 N1
+
–
PB PB
Master
N2 L2 L2‘
L1‘ L1 N1
–
+
PB PB
Slave
PE
!
!
!
!
PE
PB1
PB2
230 V~
230 V~
The PD4-M-2C-DS has a common optical system for both out-
puts. The device gets its operating voltage from both phases.
If L2 fails, the device is operated with L1 and vice versa. L1‘
‚closes only if L1 is connected and L2´ ‚ closes only if L2 is
connected.
22. Operation manual