manualshive.com logo in svg

B+B SmartWorx SPECTRE v3 LTE, Руководство пользователя, Страница: 44 / 50

Поделиться
Скачать
B+B SmartWorx SPECTRE v3 LTE Скачать руководство пользователя страница 44

7. TECHNICAL PARAMETERS

7.3.4

LTE module supports 450 MHz

LTE module supports 450 MHz

LTE parameters

Bit rate 100 Mbps (DL) / 50 Mbps (UL), UE CAT. 3
3GPP rel. 9 standard
Supported bandwidths: 5 Mhz, 10 Mhz, 20 Mhz
Supported frequencies: 450 / 800 / 1800 / 2600 MHz
Rated Output Power: B3, B7, B20, 31
MIMO (Multi-Input Multi-Output) antenna support

HSPA+ parameters

Bit rate 42 Mbps (DL) / 5,76 Mbps (UL), UE CAT. 24, 6
3GPP rel. 5, 6, 7, 8 standard
Supported frequencies: 900 / 2100 MHz
A maximum of ten HS-PDSCH channels

UMTS parameters

PS bit rate 384 kbps (DL) / 384 kbps (UL)
3GPP rel. 5, 6, 7, 8 standard
W-CDMA FDD standard
Supported frequencies: 900 / 2100 MHz
Rated Output Power: Class 3 (900 MHz and 2100 MHz)

GPRS/EDGE parameters

3GPP rel. 99 standard
Multislot Class 12
Coding schemes CS 1 to 4, MCS 1 to 9
Supported frequencies: 900 / 1800 MHz
Rated Output Power GSM/GPRS 900 MHz: Class 4
Rated Output Power GSM/GPRS 1800 MHz: Class 1
Rated Output Power EDGE 900 / 1800 MHz: Class E2

Table 28: Technical parameters of LTE module 450 MHz

36

Содержание SPECTRE v3 LTE



















































Отзывы:

Нет отзывов