B+B SmartWorx IE-MultiWay Скачать руководство пользователя страница 16

Страница: 16 / 66

-MultiWay

This screen contains the following information and options:

SAVED AND CURRENT VALUES

Saved values display the changes made during the current session and

current values display the values currently in use:

•

IP Address (IP address of SNMP agent).

•

Subnet Mask (mask to define IP subnet to which agent is connected).

•

Default Gateway (default router for IP traffic outside of the subnet).

COMMAND LIST

= Enter new

Saved Parameter Values

= Change the

Password

= Enter new

Trap Destinations

= Remove

All

Trap Destinations

= Create

SNMP Community Strings

= Delete All

SNMP Community Strings

End

the session*

Reboot

= Reboot the unit (may result in short data loss)

= Enable or disable

DHCP

Space Bar

= Opens the device specific configuration options screen.

The screens illustrated in this manual show capabilities for users with Admin rights.

Individuals with User-level rights can only view port status and port settings, change

their password, end a session, and reboot the unit.

NOTE

: It is necessary to reboot the IE-MultiWay after making any modifications to the Saved

Values for the changes to take effect. To reboot, type

Reboot

at the prompt on the Main

Configuration screen.

ASSIGNING IP INFORMATION

To modify the Saved Parameter Values (i.e., assign IP address and subnet

mask), press

. The system prompts for the IP address and subnet mask for

the connected device. Press

Enter

after each entry. A default gateway can

also be assigned, or press

Enter

to skip. When finished, press

Enter

; then

type

reboot

for changes to take effect. The Current Values can only be saved

and acted on after the IE-MultiWay has been successfully rebooted.

Содержание IE-MultiWay



































































Результаты поиска

Содержание IE-MultiWay

Отзывы:

Похожие инструкции для IE-MultiWay

Бренды по названию

Популярные бренды

B+B SmartWorx IE-MultiWay, Руководство пользователя

Результаты поиска

Содержание IE-MultiWay

Отзывы:

Похожие инструкции для IE-MultiWay

Бренды по названию

Популярные бренды