B+B Sensors 0555 0035-01 Скачать руководство пользователя страница 4

Страница: 4 / 10

TxRail-USB Temperature Transmitter
0555 0035-01, 0555 0035-02

0141 0315-951 27.09.2021

B+B Thermo-Technik GmbH | Heinrich-Hertz-Str. 4 | D-78166 Donaueschingen

Seite

von

Technische Änderungen vorbehalten

Fon +49 771 83160 | Fax +49 771 831650 | [email protected] | bb-sensors.com

Security Advices

B+B Thermo-Technik GmbH assume no liability for damages occurred through failure to observe these security advices. A usage non conform

to the instructions given in this manual can damage the device

BODY AND PROPERTY DAMAGES

The national and local standards for electrical installations must be se strictly observed.

The use of the device is strictly reserved / restricted to properly schooled / qualified operators.

The system is not adequate for use in atmosphere with explosion danger.

Do not use the system in a high electric or magnetic field area

ENSURING OF PRODUCT SECURITY

The system must be operated only within the limits given in the technical Data

Exposing the system to hot temperatures (higher than the operating temperature) will cause

damages in the electronic

circuits and also damage the housing

USAGE ACCORDING TO PURPOSE

Please use the product only for the purposes for which it is conceived. In case of doubt, please first contact B+B Thermo-

Technik GmbH

DISOPOSAL

Please return the device to B+B Thermo-Technik GmbH after expiration of its lifetime

Содержание 0555 0035-01











Результаты поиска

Содержание 0555 0035-01

Отзывы:

Похожие инструкции для 0555 0035-01

Бренды по названию

Популярные бренды

B+B Sensors 0555 0035-01, Руководство по эксплуатации

Результаты поиска

Содержание 0555 0035-01

Отзывы:

Похожие инструкции для 0555 0035-01

Бренды по названию

Популярные бренды