background image

This device is intended only for OEM integrators under the following conditions: 

 

1)

 

The antenna must be installed such that 20 cm is maintained between the antenna and 

users, and   

2)

 

The transmitter module may not be co-located with any other transmitter or antenna.   

 

As long as 2 conditions above are met, further transmitter test will not be required. However, 

the OEM integrator is still responsible for testing their end-product for any additional 

compliance requirements required with this module installed 

 

IMPORTANT NOTE:

 In the event that these conditions can not be met (for example certain 

laptop configurations or co-location with another transmitter), then the FCC authorization is 

no longer considered valid and the FCC ID can not be used on the final product. In these 

circumstances, the OEM integrator will be responsible for re-evaluating the end product 

(including the transmitter) and obtaining a separate FCC authorization. 

 

End Product Labeling 

This transmitter module is authorized only for use in device where the antenna may be 

installed such that 20 cm may be maintained between the antenna and users. The final end 

product must be labeled in a visible area with the following: “Contains FCC ID: 

TLZ-NU182H”. The grantee's FCC ID can be used only when all FCC compliance 

requirements are met. 

 

Manual Information To the End User 

The OEM integrator has to be aware not to provide information to the end user regarding how 
to install or remove this RF module in the user’s manual of the end product which integrates 

this module. 

The end user manual shall include all required regulatory information/warning as show in this 

manual. 

 

 

Содержание AW-NU182H

































Отзывы: