Azoteq AZBAT48100B Скачать руководство пользователя страница 14

 

  

 

Copyright © Azoteq (Pty) Ltd 2021. 

AZBAT48100B Product Manual 

Page 14 of 17 

All Rights Reserved. 

 

Revision 1.00 

February 2021 

 

Azoteq

PowerSense

®

 Series

 

 

Precautions 

  Storage 

1.  If  the  battery  is  stored for  more  than  3  months, it  should  be  stored  under  environmentally 

controlled conditions: 

a.  Ambient temperature: 25 ±3°C 

b.  Humidity: 25-85% RH 

c.  Air pressure: 86kPa-106kPa 

2.  Do not store the battery in direct sunlight. 

3.  The battery should be charged and discharged every 6 months. 

4.  Battery storage SOC should be ~50% 

  Safety 

  Before use 

1.  Inspect the battery to ensure that it is not damaged. If damaged, please inform the supplier. 

2.  Ensure that the installation is done by a qualified installer. 

3.  The installation needs to be done in compliance with the specified regulatory standards as 

required by governmental and local authorities. 

4.  Make sure the breaker of the battery is in the OFF position. 

5.  Ensure that the inverter is not powered from AC mains while connecting the battery. 

6.  It is advised to use suitable protection between the battery and the inverter. 

7.  Make sure  the  polarity  (positive  and  negative)  connections  between the batteries  (parallel 

use) and between the master/main battery and the inverter is correct. 

8.  The batteries 

cannot be used in series

 as the BMS is designed for a 48V battery system. 

9.  The battery/batteries need to be connected to earth and the earth resistance needs to be 

less than 1

Ω. 

10. Verify that the inverter parameters match that of the battery. 

11. The battery should be kept away from heat, fire and water. 

12. Double check all connections before switching the breaker switch to the ON position. 

 

  During use 

1.  In the event of altering or moving the installation, make sure that the breaker switch is in the 

OFF  position.  It  is  also  recommended  to  switch  the  BMS  OFF  by  press  and  holding  the 
RESET switch down for a few seconds. 

2.  Do not use this battery with that of another supplier or a different type of battery. 

3.  Do not use the batteries with a faulty or incompatible inverter. 

Содержание AZBAT48100B


















Отзывы: