background image

DOs

DONTs

    Ensure the antenna connector 

is secured tightly to the panel connector.

    Mount antenna under the open sky or at

least 50cm (20in.) beneath any object.

    Mount antenna at least 5 to 10cm (2 to 4in.)

away from wall.

    Mount antenna at least 5cm (2in.) away

from the device.
    Finalize the antenna setup to the exact

physical conditions. For example, close the 

lid, close the door, etc.

    Make sure you have a signal and a

successful data transmission by using the

mobile app.

     Do not wrap cables, zip ties, or other

items around the antenna.

     Do not attach the antenna to the

Wavelet.

IMPORTANT NOTE: 

There are a few-

minutes of delay between a successful

transmission and the use of either of 

these methods for initiating data

transmission. Repeating the use of either

method will not expedite data 

transmission.

WARNING

: If installing in a highly corrosive

environment such as a sewer, apply technical

grease to the antenna and sensor field

attachable connectors after securing them to

the panel connectors. Ayyeka recommends

using Dow Corning Molykote 55 O-Ring

Grease, though similar products can be

effective.

    If needed during installation, use the

Transmit Now

 command in the 

mobile app or the magnetic device 

activator key to initiate more rapid

transmissions.

ANTENNA MOUNTING

27

Содержание WA3888 Series





































Отзывы: