AyrKing BBS-U, Эксплуатация, обслуживание и гарантия, Страница: 4 / 9

OPERATION
(Numbers in parenthesis refer to parts view drawings)
ASSEMBLY:

Begin each day with all components clean and thoroughly dry.

Place lug (8 or 2) in bottom rails, tight against backstop.

Place dough ball pan (9) in rails underneath motor compartment.

Install dough ball chute (6) into slots inside sifter enclosure. [chute not included in BBS-EC-L models]

Position sifter screen (5) so that the end with pivot pin is located away from the motor compartment.

Install brush (4), mating end with square hole onto square drive coupling (12) and press brush towards
motor until opposite end of brush shaft clears pivot pin located on sifter screen (5). Center brush
shaft hole on pivot pin then release brush. Rotate brush by hand to assure proper installation.

Place brush cover/lug support (3), flat side up, over brush (4) so that brush cover hole is away from
motor compartment.

Place lug with hole (2) into sifter enclosure, aligning lug hole with brush cover (3) hole. Install lug plug
(1) over hole in lug.
BLENDING:

Place flour and spices in top lug (2). Press start button (16). While brush (4) is in motion, remove lug
plug (1) and push breading slowly through lug hole.

Replace lug plug (1) over hole in top lug (2). After breading has passed through sifter screen (5) and
brush (4) has stopped rotating, remove bottom lug (8) and pour breading into top lug (2). On models
that have a bottom lug with hole (2) and lug plug (2), simply interchange the top and bottom lugs.

Replace proper lug (8 or 2) tightly against backstop. Repeat steps for second blending of breading.
SIFTING:

Sifting is required after dough balls form during hand breading of product. Press start button (16).
While brush (4) is in motion, remove lug plug (1) and push breading slowly through lug hole.

Replace lug plug (1) over hole in top lug (2). After breading has passed through sifter screen (5) and
brush (4) has stopped rotating, remove bottom lug (8) and pour breading into top lug (2). On models
that have a bottom lug with hole (2) and lug plug (2), simply interchange the top and bottom lugs.

Replace proper lug (8 or 2) tightly against backstop. Occasionally empty dough ball pan (9) into trash.
Repeat above steps as often as needed.
DAILY CLEANING
(Numbers in parenthesis refer to parts view drawings)

Always disconnect power supply when servicing or cleaning machine .
NEVER SPRAY
MOTOR COMPARTMENT WITH WATER.

Remove top & bottom lugs (2 & 8), lug plug (1), brush cover (3), brush (4), sifter screen (5), dough ball
chute (6) (if equipped), and dough ball pan (9). Take all items to wash sink.

Clean table and sifter enclosure with a towel soaked in detergent/water solution. Be sure to clean all
crevices. Wipe off soapy solution using water rinsed towel until all surfaces are clean. Soak towel in
sanitizing solution (or bleach/water solution) and wipe all surfaces thoroughly.

In wash sink, spray all removed items with hose to dislodge any breading. Soak all components in
dish washing detergent and water solution.

Brush can be cleaned by using a round brush to remove soil.

After cleaning brush (4), rinse detergent solution and soak in sanitizing solution for five minutes.

After soaking, remove the brush (4) and shake away excess moisture. Place brush on square post
(27) located on top of table, by standing on end. Allow to fully air-drying before reinstalling brush (4).

Clean the sifter screen (5) and brush cover (3) in the detergent/water solution with a towel or scrub
pad if required. Rinse off detergent solution. Soak items in sanitizing solution for one minute.

Rinse dough ball chute (6) and dough ball pan (9) and replace in sifter. Reinstall sifter screen (5).
Place brush cover (3) on tabletop. Allow all components to thoroughly dry before re-using.

Clean the lugs (2 & 8) and lug plug (1) in sink with towel or scrub pad if required. Rinse off detergent
solution. Place items in sanitizing solution and soak for one minute. Place items upside down on
tabletop to air-dry. Allow all components to thoroughly dry before re-using.