42
|
43
GB
PRODUCT DESCRIPTION
OPERATION
Note!
Since the appliance and its heating coils are slightly greased when delivered, there
might be a slight development of smoke and odour the first time it is used. This is harmless
and stops after a short a while. Be sure to provide for sufficient ventilation during such time.
Warning!
Ensure that there is sufficient distance from the wall, fixtures or other appliances.
The distance must be at least 1 m to exclude the risk of fire.
Take the appliance and all the accessory parts out of the packaging.
Check that the appliance shows no signs of damage.
Select a location that is firm, level and incombustible.
Insert the mains plug into a suitable wall socket with 220 – 240 V~ 50/60 Hz and a current
carrying capacity of at least 10A.
Please be sure power switch is on “ OFF” position.
Control panel schematic diagram
；
Connect the power cord, open the back switch on the back , the machine electricity will take
into standby mode, then the light in the middle of the icon “88” is bright ,but the rest of
the light is not bright; (The switch on the back "I" is on , "O" is off).
ON/OFF“ ”:In standby mode, press the button once the machine turns on, according
to the preset functions start work (PTC low-grade open, low light is lit, the digital display
shows the ambient temperature ), press the button once again, all functions will close
and then go into standby mode; (After the machine turns off when the machine in a warm
wind state, the blower will delay to work for 10 seconds, the cold air icon will flash in
the delaying process), Then turn off the switch to "O", and then pull the plug out after using.
Temperature“ ” is used to temperature setting, press temperature once to enter into
the set state, the temperature icon flashing, the digital display shows the current set
temperature, continue to press temperature Settings (15 to 35
℃
can be set), set the
interval to 5
℃
, increase in sequence; After setting is completed, it will automatically exit
within 5 seconds if no operation on the appliance. The temperature icon stops flashing,
the digital display shows ambient temperature. At this time the machine in
accordance with the set temperature starts to work. When the ambient temperature is higher
than the set temperature, the machine will stop working, and if the ambient temperature is
lower than the set temperature, the machine will return to work.
Timing“ ” is used to set a regular shutdown time; press once to enter into the set
state, timing shutdown icon light, the icon flashing , the digital display shows the
setting time; Continue to press time once and more time setting, press 1 h interval
1.
2.
3.
4.
5.
2.
3.
4.
5.
1.
1
2
3
4
5
6
7
8
Handle
Control & display panel
Knob
Air inlet
Base
Switch
Wind net
Back cover
OSC
TEM
POWER
GEAR
REV
TIMER
sequentially, 1-8h can be set. After setting is completed, press any other key to exit, or no key
operation within 5 seconds automatically exit. The icon stop flashing , and start to
countdown, after the pending time to be finished, the machine will shutdown to enter standby
state; Timing shutdown icon and icon will no longer lit any more.
Reservation “ ” is used to set an appointment on time: In the standby mode press
once to make an appointment, the icon lit, the booking time icon flashing, the digital
display shows the setting time; Continue to press to make an appointment once and
more time setting, press 1 h interval sequentially, 1-8 h can be set. After setting is completed,
press any other key to exit, or no key operation within 5 seconds automatically exit. The icon
stop flashing , and start to countdown, After the pending time to be finished , the machine will
start to work in the state which set by the appointment. the corresponding indicator icon lit,
and reservation icon will turn off .
Swing“ ”: open/close oscillating function: in the working state, press the icon once,
oscillating function will start to work , the icon lit; Press the icon once again,
oscillating function will close, and the icon will turn off.
Gear“ ”is used to set the machine work gear: the default boot is low-grade warm wind,
the icon lit; Press once, it will switch to high-grade warm wind, high-grade warm
wind icon on ; Then press once again, it will switch to the cold wind, that icon
on; Third gear button to switch to a low-grade warm wind again, the icon lit; then follow
in recycling.
CLEANING AND MAINTENANCE
Before undergoing maintenance, please disconnect the power cord plug out the power source,
can be carried out after warm air blower cooling
；
The surface area of dust, with a soft cloth to wipe;When the surface is too dirty, available
below 50 degrees Celsius of the mixture of water and neutral detergent touch water to wipe
with a soft cloth and dry
；
Do not use while clean gasoline, days that water, diluent and any easy to damage the surface
material; Because these things may react with heater and cause discoloration
；
Product when not in use for a long period of time, unplug the power plug, wrap the machine to
prevent dust into the machine
；
When the heater should be cold, dry, packaged storage and dry ventilated place
；
as this may
damage the appliance.
