AXXIS KLINCH-PAK KP-APN-22 Скачать руководство пользователя страница 10

 10 

1320 Tower Road  Schaumburg, IL  60173 

Phone:  

888-392-9947

   Fax:  

877-393-2948

 

TROUBLE SHOOTING 

PROBLEM

 

CAUSE

 

REMEDY

 

AIR LEAKAGE FROM 
TRIGGER .

 

O-RING ON VALVE 

016

OR 

ON TUBE

017

ARE 

DAMAGED .

 

O-RING MUST BE REPLACED

 

AIR LEAKAGE FROM 
EXHAUST PORT .

 

O-RINGSON VALVE

016

OR 

ON TUBE

017

ARE 

DAMAGED .

 

O-RING MUST BE REPLACED

 

PISTON’S O-RING

507

IS 

DAMAGED .

 

O-RING MUST BE REPLACED

 

AIR LEAKAGE RROM 

CYLINDER

004

). 

PISTON ROD PORT

007

O-

RING

519

IS DAMAGED .

 

REPLACE THE O-RING .

 

SLOW AND SHORT 

TRAVEL CYCLING

 

CHECK FOR LOOSED SCREW

517

AND WEAR OF PARTS

014,009

) 

POSITION ECCENTRIC PIN

013

AS SHOWN 

AND TIGHTEN SCREW 

(

517)

.   

IF SHORT TRAVEL 

OCCURS ADJUST PIN POSITION IN AN UPWARD 
POSITION.  IF SLOW CYCLE ADJUST PIN IN A 
DOWNWARD DIRECTION.

 

 

EXCESSIVE JAMS

: 

SLOW AND SHORT TRAVEL 
CYCLING .

 

CHECK AS NOTED IN SLOW AND SHORT TRAVEL 

CYCLING SECTION .

 

ANVIL SCREWS LOOSE .

 

TIGHTEN SCREWS

 

STAPLE SIZE IS WRONG .

 

USE THE PROPER SIZE STAPLE

 

INSUFFCIENT LUBRICATION

 

SUITABLY CLEAN AND LUBRICATE

 

UNEVEN CLINCH

 

WRONG STAPLE SIZE

 

CHECK FOR PROPER LEG LENGTH 
ADJUSTMENT & CLINCHER SIZE .

 

UNCLINCHED 
STAPLE

 

ANVIL

021,022

LOOSE

 

TIGHTEN ANVIL

021,022

) 

ANVIL

021,022

ARE BROKEN

 

REPLACE ANVIL

021,022

) 

SLOW AND SHORT TRAVEL 
CYCLING .

 

CHECK AS NOTED IN SLOW AND SHORT 
TRAVEL CYCLING SECTION .

 

Содержание KLINCH-PAK KP-APN-22













Отзывы: