background image

2

CONNECTIONS TO BE MADE

From the 16-pin harness to the aftermarket radio:

 • Connect the 

Red

 wire to the ignition wire.

 • Disregard the 

Orange/White

 wire, it will not be used in this application.

 • Connect the 

White

 wire to the left front positive speaker output.

 • Connect the 

White/Black

 wire to the left front negative speaker output.

 • Connect the 

Gray

 wire to the right front positive speaker output.

 • Connect the 

Gray/Black

 wire to the right front negative speaker output.

 • Connect the 

Green

 wire to the left rear positive speaker output.

 • Connect the 

Green/Black

 wire to the left rear negative speaker output.

 • Connect the 

Purple

 wire to the right rear positive speaker output.

 • Connect the 

Purple/Black

 wire to the right rear negative speaker output.

 • Connect the 

Blue/White

 wire to the amp turn on wire.

 • Connect the 

Brown

 wire to the mute wire. If the aftermarket radio does not have a “mute” 

wire, tape off the 

Brown

 wire.

The following (3) wires are for aftermarket multimedia/navigation radios that provide these 

wires (if not required, tape them off and disregard them):

 • Connect the 

Light Green

 wire to the parking brake wire (if applicable).

 • Connect the 

Blue/Pink

 wire to the speed sense wire (if applicable).

 • Connect the 

Green/Purple

 wire to the reverse wire (if applicable).

  •  Plug the 16-pin harness into the CHTO-02.

From the 22-pin Chrysler harness to the aftermarket radio:

 • Connect the 

Yellow

 wire to the 12-volt battery or memory wire.

 • Connect the 

Black

 wire to the ground wire.

 • Connect the 

Orange

 wire to the illumination wire. If the aftermarket radio has no 

illumination wire tape off the 

Orange

 wire.

  •  Plug the 14-pin harness into the CHTO-02.

12-pin pre-wired ASWC-1 harness:

  •  This harness is to be used in along with the optional ASWC-1 (sold separately) to retain 

steering wheel audio controls. If the ASWC-1 is not being used, disregard this harness. If it 
will be used, please refer to the ASWC-1 instructions for radio connections and programming.

 Note: 

Disregard the harness that comes with the ASWC-1.

Содержание CHTO-02

Страница 1: ...n harness to 22 pin Chrysler harness with stripped leads TOOLS REQUIRED Cutting tool Crimping tool Tape Connectors example butt connectors bell caps etc TABLE OF CONTENTS Connections to be made 2 Installing the CHTO 02 3 Testing the CHTO 02 3 Chrysler Dodge amplified data interface 2002 2008 APPLICATIONS Provides accessory 12 volt 10 amp Retains R A P retained accessory power Used in amplified syste...

Страница 2: ...ff the Brown wire The following 3 wires are for aftermarket multimedia navigation radios that provide these wires if not required tape them off and disregard them Connect the Light Green wire to the parking brake wire if applicable Connect the Blue Pink wire to the speed sense wire if applicable Connect the Green Purple wire to the reverse wire if applicable Plug the 16 pin harness into the CHTO 0...

Страница 3: ...tive battery terminal Cycle the key by turning the ignition on for 30 seconds Then off and on again to test the radio Turn the ignition on if not already and then turn the radio on to verify that the radio works Check balance and fader controls for proper operation To adjust the overall volume of your audio system rotate the potentiometer which is located on the 16 pin side of the interface clockw...

Страница 4: ...certified technicians IMPORTANT If you are having difficulties with the installation of this product please call our Tech Support line at 1 800 253 TECH Before doing so look over the instructions a second time and make sure the installation was performed exactly as the instructions are stated Please have the vehicle apart and ready to perform troubleshooting steps before calling axxessinterface com ...

Отзывы: