manualshive.com logo in svg

Axon Synapse SCV12, Техническое руководство

Поделиться
Скачать
Axon Synapse SCV12 Скачать руководство пользователя страница 17

17 

Add_on A1 ~ 

Add_on B4 

This item indicates the status of the audio, which is present in 
addon A1 till addon B4. 

OK

 indicates that the audio channels are 

present, 

NA

 indicates the audio is not available. 

 

 

ANC-stat 

ANC-stat

, Ancillary Status, indicates that embedded audio is 

present and valid. 

ANC-stat

 indicates if an input signal is 

OK

, 

NA

 (not available) or 

Error

. 

 

 

EDH- Stat 

EDH-Stat

, indicates the status of the EDH within the incoming 

SDI 

signal. OK

 is indicated if the status of the detected EDH 

does not indicate errors. 

UES

 is shown if an EDH data block is not present. 

EDA

 is displayed if an EDH error has previously been detected by 

another card in the SDI chain. 

EDH

 is displayed if a previously undetected EDH error is detected 

by this device. 

 

 

FILT-Stat 

This status item displays the current active status of the Luma-
filter setting. Can be one of the following statuses: 
-

 

LPF_NTSC 

-

 

LPF_PAL 

-

 

Notch_NTSC 

-

 

Notch_PAL 

-

 

SSAF 

-

 

CIF 

-

 

QCIF 

 

 

Standard-Stat 

This status item displays the current active status of the Standard 
setting. Can be one of the following statuses: 
-

 

NTSC 

-

 

PAL_BGHID 

-

 

PAL_M 

-

 

PAL_N 

 

 
 
 
 
 
 
 

Содержание Synapse SCV12
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды