background image

PARTS IDENTIFICATION AND DESCRIPTION

Please take some time to identify the various parts of your machine so that you are
familiar with the terminology we will use to enable you to set up and operate your Mill
safely and correctly.

Main tool post 

This is the column of the mill, it is an 65 x 50 bar with a dovetail 
slide machined on the front onto which the milling head is       
mounted, the lower part is the circular ʻbossʼ for the tilt assembly. 
On the left side of the post a scale, graduated in mmʼs, is mounted 
to read against an adjustable pointer mounted on the head casting. 

Rise and fall

The Rise and Fall drive screw is anchored in a machined housing 
at the top of drive screw the main tool post. It has a wheel and rod 
handle keyed to the shaft to enable the screw to be turned. It is fed 
through a threaded dog that is bolted to the head casting allowing 
the head to be moved up and down. Viewed from above the drive 
screw is turned clockwise to raise the head and anti-clockwise to 
lower it.

Tilt housing

The tilt housing is mounted to the base casting using 4 bolts. The 
tilt ʻbossʼ of the main tool post is mated to the housing and 
clamped by a urther 4 bolts. The main tool post can tilt 45 
(degrees) from the vertical either left or right. There is an 
adjustable pointer and a scale mounted on the housing to give an 
indication of the amount of tilt that has been applied.

Milling head         

This is the ʻmilling machineʼ and the descriptions of its        
various parts and components are detailed as follows:-

Milling head

The main casting to which all the components are attached. The 

casting

head has a dovetail housing machined at the rear, which allows 
the casting to be fitted to the Main Tool Post. The left side of the 
dovetail slide is fitted with a gybe strip to maintain the fit.

Head clamp

Located between the gybe strip adjusters and locknuts is an handled 
bolt that clamps the gybe strip against the slide to effect a locking 
action for the rise and fall of the head. 

Rise and fall 

An ʻLʼ shaped casting that is threaded to accept the rise and fall 

drive screw dog

drive screw, and is driven along the thread when the screw is 
turned. As it is bolted to the milling head, the head will therefore 
follow its movement as it is being driven.

Motor and

The motor and gearbox assembly are mounted above the main 

gearbox

head casting at the top of the arbor sleeve. The motor drive is 
geared through to the spindle with an intermediate 2:1 gearbox.

26

Содержание SIEG C4











































Отзывы: