manualshive.com logo in svg

Axminster 107651, Оригинальное руководство пользователя

Поделиться
Скачать
Axminster 107651 Скачать руководство пользователя страница 30

ROUTING MAINTENANCE

30

Clean out impacted ‘crud’ and saw dust

Clean out impacted ‘crud’ and saw dust

DISCONNECT THE SAW FROM 
THE MAINS SUPPLY!

Daily

• Keep the machine clean.
 
• Check the saw blade for missing teeth and cracks, see fig  82
 
• Spray oil the bare metal surfaces. 
 
• If you are constantly using the bandsaw during the day, open 
up the wheel doors and clean out all the compacted saw dust.

Weekly

• Open the top and bottom wheel covers and clean out all the 
saw dust with in.

Fig 80

Monthly

• Open the lower and upper door and check the 
condition of the tyres and the drive belt, see figs 81-82-83.

• Clean impacted ‘crud’ from the tyres, apply a little oil to the 
screw threads of the blade and drive belt tensioners. DO NOT 
USE OIL near the belt.

• The pivots and the slides of the top wheel mounting
assembly and the captive stub axle of the belt tensioner in its 
slot could likewise be lightly oiled.
 
• Using an air line (wearing goggles) blow out the motor 
casing.

Fig 81-82-83

A

B

• Check the condition of the tyres (A)
• Check for missing teeth (B)
• Check the condition of  the drive belt (C)

C

IMPORTANT NOTE: If you are cutting metal, clean the lower 
blade guides and lower wheel daily!

Содержание 107651













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды