background image

 

 

iii 

Safety Precautions 

 

Before getting started, please read the following important safety precautions. 

1. 

The  UST210-83K-FL  does  not  come  equipped  with  an  operating  system.  An 
operating  system  must  be  loaded  first  before  installing  any  software  into  the 
computer. 

2. 

Be  sure  to  ground  yourself  to  prevent  static  charge  when  installing  the  internal 
components. Use a grounding wrist strap and place all electronic components in 
any  static-shielded  devices.  Most  electronic  components  are  sensitive  to  static 
electrical charge. 

3. 

Disconnect  the  power  cord  from  the  UST210-83K-FL  before  making  any 
installation.  Be  sure  both  the  system  and   the  external  devices  are  turned  OFF. 
Sudden surge of power could ruin sensitive components. Make sure the UST210-
83K-FL is properly grounded. 

4. 

Make  sure  the  voltage  of  the  power  source  is  correct  before  connecting  the 
equipment to the power outlet.  

5. 

Turn OFF the system power before cleaning. Clean the system using a cloth only. 
Do not spray any liquid cleaner directly onto the screen.   

6. 

Do  not  leave  this  equipment  in  an  uncontrolled  environment  where  the  storage 
temperature is below -45

 or above 85

. It may damage the equipment.  

7. 

Do not open the system

s back cover. If opening the cover for maintenance is a 

must,  only  a  trained  technician  is  allowed  to  do  so.  Integrated  circuits  on 
computer boards are sensitive to static electricity. To avoid damaging chips from 
electrostatic discharge, observe the following precautions:  

 

Before  handling  a  board  or  integrated  circuit,  touch  an  unpainted  portion  of 
the  system  unit  chassis  for  a  few  seconds.  This  will  he lp  to  discharge  any 
static electricity on your body.  

 

When  handling  boards  and  components,  wear  a  grounding  wrist  strap, 
available from most electronic component stores . 

8. 

This  product  is  intended  to  be  supplied  by  a  Listed  Power  Adapter  or  DC  power 
source. Output meets SELV limits, rated 12-24Vdc, minimum 1.6-0.81A, Tma = 25 
degree  C,  and  the  altitude  of  operation  =  5000m.  Supported  POE  rated  24Vdc, 
minimum 1.95A Tma = 25 degree C, and the altitude of operation = 5000m.  

If you need further assistance while purchasing the power source, please contact 
the manufacturer for further information.  

 

CAUTION

 

Risk  of  explosion  may  occur  if  the  battery  is  replaced  by  an  incorrect  type.  Dispose 
of used batteries according to the instructions.  

 

WARNING  

 

Do not touch the hot surface of the system unit when it is turned on.  

 

Restricted access area: The equipment should only be installed in a Restricted 
Access Area. 

 

 

 

Содержание UST210-83K-FL Series


























































Отзывы: