AXIOMTEK IMB200 Скачать руководство пользователя страница 61

Страница: 61 / 77

IMB200 LGA775 ATX MB User Manual

Award Bios Utility

The choice: Half, Full.

UR2 Duplex Mode

Half:

Data is completely transmitted before receiving

Data

Full:

Transmits and receives data simultaneously.

Onboard Parallel Port

378/IRQ7, 3BC/IRQ7, 278/IRQ5 Select the I/O

address and IRQ for the onboard parallel port.

Disabled

: Disables the onboard parallel port.

Parallel Port Mode

The options are SPP, EPP, ECP and ECP+EPP. These apply to a

Standard specification and will depend on the type and speed of

You device. Refer to your peripherals manual for the best option.

SPP

– Allows normal speed operation but in one direction

only.

ECP

(Extended Capabilities Port)

– Allow parallel port to

operate in bidirectional mode and at a speed faster then
the normal mode’s data transfer rate.

EPP (

Enhanced Parallel Port)

– Allows bidirectional

parallel port operation at maximum speed.

ECP mode Use DMA

This is used to select a DMA channel of the parallel port.

7.6.4 Onboard UART 3/4

Use the onboard UART. In this mode you should use the
Picasso SDK UART-functions. The. Data will be set to the RS-
232 a connector

Содержание IMB200














































































Результаты поиска

Содержание IMB200

Отзывы:

Бренды по названию

Популярные бренды

AXIOMTEK IMB200, Руководство пользователя

Результаты поиска

Содержание IMB200

Отзывы:

Бренды по названию

Популярные бренды