LIMITED WARRANTY
Proel warrants all materials, workmanship and proper operation of this product for a period of two years from the original date of purchase. If any defects are found
in the materials or workmanship or if the product fails to function properly during the applicable warranty period, the owner should inform about these defects the
dealer or the distributor, providing receipt or invoice of date of purchase and defect detailed description. This warranty does not extend to damage resulting from
improper installation, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units, and when the unit has been properly used and warranty is still
valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible for any “direct damage” or “indirect damage” caused by product defectiveness.
• This unit package has been submitted to ISTA 1A integrity tests. We suggest you control the unit conditions immediately after unpacking it.
• If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspection.
• Proel is not responsible for any damage that occurs during shipment.
• Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.
• Possible damages to unit should be immediately notified to forwarder. Each complaint for package tampered with should be done within eight days from product
receipt.
SAFETY INSTRUCTIONS
– To reduce the risk, close supervision is necessary when the product is used near children.
– Protect the apparatus from atmospheric agents and keep it away from water, rain and high humidity places.
– This product should be site away from heat sources such as radiators, lamps and any other device that generate heat.
– This product should be located so that its location or position does not interfere with its proper ventilation and heating dissipation.
– Care should be taken so that objects and liquids do not go inside the product.
– The product should be connected to a power supply mains line only of the type described on the operating instructions or as marked on the product. Connect the
apparatus to a power supply using only power cord included making always sure it is in good conditions.
– WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
– Do not cancel the safety feature assured by means of a polarized line plug (one blade wider than the other) or with a earth connection.
– Make sure that power supply mains line has a proper earth connection.
– Power supply cord should be unplugged from the outlet during strong thunderstorm or when left unused for a long period of time.
CE CONFORMITY
Proel products comply with directive 2004/108/EC (EMC), as stated in EN 55103-1 and EN 55103-2 standards and with directive 2006/95/CE (LVD), as stated in EN
60065 standard.
PROEL S.p.A. (World Headquarter) - Via alla Ruenia 37/43 - 64027 Sant’Omero (Te) - ITALY
Tel: +39 0861 81241 Fax: +39 0861 887862 www.axiomproaudio.com
Stacked installation
WARNING!
• The ground where the KPTAX2012P Fly bar serving as ground support is
placed needs to be absolutely stable and compact.
• Adjust the feet so to lie the bar perfectly horizontal.
• Always secure ground stacked setups against movement and possible
tipping over.
• A maximum of 4 x AX2010 cabinets with the KPTAX2012P Fly bar serving
as ground support are allowed to be set up as ground stack.
In the stack configuration you have to use the three optional BOARDAC2P feet and
the fly bar must be mounted upside down on the ground.
Coupling system in the front do not require any adjustment: using two locking pins
each loudspeaker box is fixed to the previous. The slotted bar in the back is inserted
in a U-shaped frame which features a series of numbered holes. Sliding the slotted
bar in the U-shaped frame of the next loudspeaker and inserting a locking pin in
one of the numbered holes, it is possible to adjust the relative splay angle between
two adjacent loudspeakers in the array column.
The optimal splay angles can be simulated using the EASE Focus 2 software.
KPTAX2012P STACKED ARRAY
CENTER OF GRAVITY
max splay angle 5°
max splay angle 10°
max splay angle 10°
max splay angle 10°
