background image

AX-160IP - TOUCH PAD DIGITAL MULTIMETER - USER’S

MANUAL

1. GENERAL INSTRUCTIONS

1.0.

This instrument complies with IEC 61010-1, CAT III 1000V and CAT IV 600V overvoltage standards. See
Specifications.
- Touch pad operation.
- 6000counts, daul value display.
- IP65 water jets.
- CAT III 1000V / CAT IV 600V application.
- Auto backlight.
- Digital calibration.
- 2 colour backlight for various operate status indication.
- Chargeable battery selection/ MicroUSB charge
To get the best service from this instrument, please read carefully this user’s manual and respect the
detailed safety precautions.
International symbols used on the meter and in this manual are explained in chapter 1.2.

1.1. Precautions safety measures

1.1.1. Preliminary

* As the possibilities of high transient overvoltages occurred in today’s power systems increase, more
stringent safety standards are set for the electrical test equipment. Transients on electrical systems(power
grid, feeder or branch circuits) will trigger a series of incidents that may result in serious personal injury.
To protect you against transients, safety must be built into the test equipment.
Overvoltage category /// In brief /// Examples
- CATI/// Electronic /// • Protected electronic equipment.
• Equipment connected to (source) circuits in which measures are taken to limit transient overvoltages to
an appropriately low level.
• Any high-voltage, low-energy source derived from a highwinding resistance transformer, such as the
high-voltage section of a copier.
- CATII/// Single-phase receptacle connected loads /// • Appliance, portable tools, and other household and
similar loads.

Содержание AX-160IP































Отзывы: