State of the art 2017-01-27 - Technical changes, design modifications,
errors and misprints are subject to change without prior notice.
Safety advice:
4
Installation and repairs to the equipment may only be carried out by
technicians observing the current VDE guidelines. No liability will be
assumed in the case of faulty installation and commissioning.
4
Before opening the equipment pull out the power plug or remove the
power supply, otherwise there is danger of electrocution. This is also
valid for cleaning the equipment or working on the connections.
4
Providing that a serviceable fuse exists, the power plug must be pulled
out before changing the fuse. Defective fuses may only be replaced with
standard compliant fuses that have the same nominal value.
4
The equipment may only be operated in dry rooms. In humid rooms or
outdoors there is danger of short-circuit (caution: risk of fire) or
electrocution.
4
To prevent damage to your equipment and to avoid possible peripheral
damages, the devices foreseen for wall mounting may only be installed
on a flat surface.
4
Choose the location of installation or mounting so that the power plug
can be reached and pulled out of the socket easily in case of danger.
Choose the location of installation or mounting such that children may
not play unsupervised near the equipment and its connections. The
location of installation or mounting must allow a safe installation of all
cables connected. The mains cable as well as feeder lines may not be
damaged or clamped by objects of any kind.
4
Choose the location of installation or mounting so that under no
circumstances liquids or objects can get into the equipment (e.g.
condensation, water coming from leaking roofs or flowing water, etc.).
4
Avoid exposure of the equipment to direct sunlight and to other heat
sources (e. g. radiators. other electrical devices, chimney, etc.). Devices
that are equipped with heat sinks or ventilation slots must under no
circum-stances be covered or blocked. Also ensure for a generous air
circulation around the equipment. In this way you avoid possible
damage to the equipment as well as a risk of fire caused by
overheating. Absolutely avoid that cables come near any source of heat
(e.g. radioators, other electrical devices, chimney, etc.).
WEEE Nr.
DE26869279
Your device is marked with the WEEE symbol (Waste Electronics
and Electrical Equipment). This means that the electrical and
electronic components must not be disposed of as residual waste.
Used electrical and electronic components must be disposed of
separately.
SKT 20-20M
SKT 40-20M | SKT 80-20M
SKT 40-24M | SKT 80-22M
Multituner | DVB-T2
twin/quattro/octo module
Quick start guide
Manufacturer
AXING AG
Gewerbehaus Moskau
8262 Ramsen
EWR contact adress
Bechler GmbH
Am Rebberg 44
78239 Rielasingen
Technical Data:
SKT 20-20M
Ducts
2
Multituner
2 × DVB-S/S2/T/T2/C
Inputs
2 × F Buchse
Outputs
1 × F-Stecker Quickfix
Current consumption
16V=/1,5 A
Data interface
1 × RJ 45
SKT 40-2xM
SKT 80-2xM
Ducts
4
8
Multituner
4 × DVB-S/S2/T/T2/C
8 × DVB-S/S2/T/T2/C
Inputs
4 × F Buchse
8 × F Buchse
Outputs
1 × F-Stecker Quickfix
2 × F-Stecker Quickfix
Current consumption
16V=/1,5 A
16V=/3 A
Data interface
1 × RJ 45
2 × RJ 45
All modules
Input
Frequency range TERR | SAT 100…860 MHz | 950…2150 MHz
Input level TERR | SAT
45…85 dBµV | 43...84 dBµV/-65 … -25 dBm
LNB
voltage
13/17 V; 22 kHz on/off; DiSEqC 1.0
Max.
LNB current (per input)
250 mA
Symbol rate
1,5…45 MS/s
Error correction
automatisch
Transport stream
MPEG-2 ISO/IEC 13818 | MPEG-4 ISO/IEC 14496
Output
Frequency range
114…858 Mhz
Output channels
S2…K69
Modulation
QPSK, QAM 16, 64, 256
FET
2k / 4k mode
FEC
1/2, 3/5, 2/3, 3/4, 4/5, 5/6
Guard Interval
1/4, 1/8, 1/16, 1/32
Norm
CCIR, Australia
Output level
80…100 dBµV
MER
> 39 dB
Ambient temperature range
-10°C…+50°C
Dimensions approx.
72 mm × 218 mm × 129 mm
SKT 40-24M
SKT 80-22M
Common Interface
4
2
