Manufacturer
AXING AG
Gewerbehaus Moskau
8262 Ramsen
EEA contact address
Bechler GmbH
Am Rebberg 44
78239 Rielasingen
State of the art 2020-04-03
Technical improvements, changes in design, printing- and other errors expected.
Safety advices:
Installation and repairs to the equipment may only be carried out by
technicians observing the current guidelines. No liability will be assumed
in the case of faulty installation and commissioning.
Before handling the device, disconnect the power supply, otherwise there
is danger to life. This also applies if you clean the device or work on the
connections.
Providing that a serviceable fuse exists, the power plug must be pulled
out before changing the fuse. Defective fuses may only be replaced with
standard compliant fuses that have the same nominal value.
The equipment may only be operated in dry rooms. In humid rooms or
outdoors there is danger of short-circuit (caution: risk of fire) or
electrocution.
To prevent damage to your equipment and to avoid possible peripheral
damages, mount the device only on flat surfaces.
Choose the location of installation or mounting such that children may
not play unsupervised near the equipment and its connections.
The location of installation or mounting must allow a safe installation of
all cables connected. Connected cables must not be damaged or crushed
by any objects.
Absolutely avoid that cables come near any source of heat (e.g.
radioators, other electrical devices, chimney, etc.).
Choose the location of installation or mounting so that under no
circumstances liquids or objects can get into the equipment (e.g.
condensation, water coming from leaking roofs or flowing water, etc.).
Avoid exposure of the equipment to direct sunlight and to other heat
sources (e. g. radiators. other electrical devices, chimney, etc.).
Devices that are equipped with heat sinks or ventilation slots must under
no circum-stances be covered or blocked. Also ensure for a generous air
circulation around the equipment. In this way you avoid possible damage
to the equipment as well as a risk of fire caused by overheating.
In case of damage, interrupt the power supply immediately.
Do not try to repair the device. This device should only be serviced or
repaired by qualified service personnel. Contact your distributor for more
information.
Do not open the device.
For disassembly always pull the mains plug first and disconnect the
power supply cable from the connected device.
SPU 58-06 | SPU 512-06
SPU 516-06 | SPU 524-06
SPU 532-06
basic
-line
Multiswitches /
Cascade units
Operation instructions
Technical data:
CE Confirmation Declaration
Hereby, AXING AG declares that the device is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address:
https://axing.com/en/downloads/ce/
.
WEEE Nr. DE26869279 | Electrical and electronic components must not be disposed of
as residual waste, it must be disposed of separately.
Type
SPU 58-06
SPU 512-06
SPU 516-06
SPU 524-06
SPU 532-06
Inputs
Number
5
Frequency range
5…862 MHz | 950…2400 MHz
Max.
LNB current
1500 mA
Isolation
V | H.
>30 dB
Isolation
TERR | SA
T
30 dB
Subscriber ports
Number
8
12
16
24
32
Switch commands
13/18
V,
0/22 kHz
Tap
loss TERR
23 dB ±2 dB
27 dB ±3 dB
27 dB ±3 dB
33 dB ±3 dB
33 dB ±3 dB
Tap loss SA
T
-1...-3 dB ±2 dB
-1...-2 dB ±2 dB
-1...-2 dB ±2 dB
2...-1 dB ±2 dB
2...-1 dB ±2 dB
Max.
output level SA
T (3rd or
-
der SA
T EN 50083
-3 35dB KMA,
2 sender test method)
102 dBµV
Current consumption per port (without LNB supply)
< 35 mA
Trunk outputs
Number
5
Through
loss TERR
2 dB ±1 dB
2…3 dB ±1 dB
2…3 dB ±1 dB
2 dB ±2 dB
2 dB ±2 dB
Through loss SA
T
2 dB ±1 dB
2…4 dB ±1 dB
2…4 dB ±1 dB
2…6 dB ±2 dB
2…6 dB ±2 dB
Connector
s
Connector type
F
Gener
al
Equipotential bonding connection
4 mm²
Operating temperature range (acc.
to EN 60065)
-20…+50°C
Dimensions (W × H × D) appr
.
112 x 137 x 63 mm
150 x 137 x 63 mm
150 x 137 x 63 mm
240 x 137 x 63 mm
240 x 137 x 63 mm
Protection class
IP 20
