Axel Falcon 15 Скачать руководство пользователя страница 30

Страница: 30 / 73

IN & OUT SETTINGS (FM VERSION)

ENG

Page 30

Escape from the

Output Level

menu and enter the

Output Mode

menu.

Select the

Peak Reference Tone

option.

The Peak Tone identifies the maximum peak value of the audio and MPX signals reached by the processor while it is

operating. This peak corresponds to the maximum frequency deviation. This allows you to set the levels for the entire sound

chain simply and safely.

The Peak Tone consists of a 500 Hz/ 0 dBm tone + a 19 kHz / - 20 dB pilot tone (the pilot signal may be disabled by

selecting the

Off

option within the

MPX Module

menu before enabling the

Peak Reference Tone

mode).

Once you have enabled the Peak Tone, adjust the Mpx Output Level until You reach the desired

modulation deviation.

Select the

Normal Operation

option in the

Output Mode

(Normal Operation mode allows a normal use of the equipment and all its functions)

NOTE: THE PROCESSOR FACTORY SETTINGS ARE 0 dB FOR BOTH INPUT AND OUTPUT.

TO ACHIEVE THE BEST AUDIO QUALITY, WE RECOMMEND NOT TO LOWER THE OUTPUT

LEVEL AND TO ADJUST THE EQUIPMENT CONNECTED TO THE PROCESSOR (STEREO

ENCODERS, EXCITERS, ETC.) RATHER THAN THE PROCESSOR ITSELF.

12.3.4 CALIBRATING THE PILOT LEVEL AND PHASE

The

Mpx Module / Pilot Level

menu allows you to adjust the amount of 19kHz pilot tone injected into the

composite signal (expressed in dB). Factory-default value is – 20 dB (+/- 7.5 kHz carrier deviation) compared to

the overall Stereo Composite MPX signal. Level may be adjusted within the range of -25 dB to -15.5 dB, in 0.1 dB

steps. Pilot tone may also be disabled by turning the jog-wheel anti-clockwise to Off.

The

Mpx Module / Pilot Phase

menu allows you to adjust the phase relationship between the 19 kHz pilot and

the 38 kHz modulator. This can be used to correct for inconsistencies among different transmitters. It may be

adjusted from -12.0 to + 12.0 degrees (Deg) in 1 deg steps

12.3.5 ENABLING SYNC OUTPUT

When required, Falcon 15 can supply TTL pilot synchro signal (19 kHz, square wave, 5 Vpp) on the Sync Out

connector.
To do this, enter the

Mpx Module Setup / Output Sync

menu and select

Output Sync Enabled

option.

Содержание Falcon 15










































































Результаты поиска

Содержание Falcon 15

Отзывы:

Axel Falcon 15, Руководство по эксплуатации, Страница: 30 / 73

Результаты поиска

Содержание Falcon 15

Отзывы: