background image

                                                                                                                                     

Steps To Test Run Before Installation

IMPORTANT! 

Wear gloves to protect against sharp edges.

PLEASE FOLLOW THESE INSTRUCTIONS TO TEST THE 
RANGE HOOD BEFORE INSTALLATION FOR ANY DEFECTS 
OR SHIPPING DAMAGE:

1.  Remove the range hood and accessories from the 

package carefully.

2.  Place the range hood on a flat stable surface, 

remove the baffle filter and check for any dents or 
damages on the range hood body.

3.  Remove the loosen parts if there's any.
4.  Plug the range hood into a 120V AC power source. 

Press the power button once and then any of the 
speed buttons to turn it on.

5.  Check each speed variation and pay attention to 

the noise level to make sure there isn't any unusual 
noise besides it coming from the wind blowing. 
Press the Light Button to check the lights.

6.  Verify all functions, as instructed in Page 8, are 

working properly.

7.  Refer to Range Hood Troubleshooting in Page 10 for 

general issues and solutions.

Please read all instructions carefully before proceeding 
further to prevent the risk of fire, electric shock, personal 
injury or damage to the range hood. This manual 
provides a general insight on the installation and may 
not include solutions for all possible issues that may 
occur. 

In case of this manual destroyed or lost, please visit 
https://www.awoco.com and download a digital version.

Installation Overview

1.  Unpack the range hood and check for any physical 

damage on the body.

2.  Test run the range hood and check if all functions 

are working properly. Refer to Page 8

 

for 

functionalities.

DO NOT

 

install the range hood if it's defective. Contact 

the seller immediately.

3.  If all is fine, install the range hood as instructed in 

this manual. Refer to Page 7.

4.  Test run the range hood again when the installation 

is finished. Refer to Page 10

 

for troubleshooting.

Possible Tools Needed:

•  Marker / Pencil;
•  Jig Saw or Reciprocating Saw;
•  Screwdrivers or Power Drill;
•  Level;
•  Measuring Tape;
•  Knife:
•  Duct / Foil Tape;
•  Screws.

2 PEOPLE ARE REQUIRED FOR THE INSTALLATION.

                                                                                                                                     

Содержание 6" Height Under Cabinet Series













Отзывы: