Awntech Houstonian Скачать руководство пользователя страница 21

Page | 21 

 

Freight expenses to and from Awntech Corporation are not covered by this Warranty and must be paid by 
the purchaser. 

 

A bottle of touch up paint is included with each awning.  It is the responsibility of the purchaser to inspect 
their awning for scratches or exposed metal. It is the responsibility of the purchaser to liberally apply touchup 
paint to any identified areas during their inspection for scratches or exposed metal. Ignoring scratches or 
exposed metal will allow for corrosion or rust in the afflicted areas. 
 

H. GENERAL PROVISIONS AND LIMITATIONS 

 

The warranty granted herein is the exclusive remedy for the purchaser. Awntech Corporation makes no 
other warranties to the purchaser, express, statutory, implied or otherwise and all implied warranties, 
including without limitations, implied warranties of merchantability and fitness for a particular purpose, are 
hereby disclaimed. 

 

To the extent permitted by law, Awntech Corporation shall have no liability to the purchaser or any other 
person for incidental, special, consequential, indirect or similar damages of any kind or nature whatsoever, 
whether arising out of breach of warranty or other breach of contract, negligence or other tort, or otherwise, 
even if Awntech Corporation shall have been advised of the possibility or likelihood of such potential loss or 
damage. In no event shall Awntech Corporation be liable for loss of profits and/or wages. 

 

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or 
limitation of incidental or consequential damages, so the above limitations may not apply to you. 
This warranty gives you specific rights, and you may have other rights, which vary from state to state. 
 
Awntech Corporation, 10950 S. Pipeline Rd., Bldg. 1, Euless, TX 76040 / Ph 817-354-9600; Fax 817-354-
9612 / 

[email protected]

 

RETURNS & DAMAGES

 

RETURN QUALIFICATION:

 

You can only return a product if it is defective upon arrival.  If you simply do not like the product or if you did not 
measure correctly, you will only be qualified for a merchandise credit and you will be required to pay for shipping the 
product back to Awntech in re-stock condition. There will be a 25% restock fee applicable.  Concealed damage must 
be reported within 7 days from the receipt of the awning. 

DAMAGED MATERIAL:

 

Damage occasionally occurs during shipping. Scrapes dents and rips in the outer packaging that could indicate 
possible damage should be described to the carrier at the time of delivery.  If damage to the product seems apparent, 
the shipment should be refused. 

RETURNS/ORDER EXCEPTIONS: 

Phone :817-354-9600, Fax 817-354-9612, E-mail 

[email protected]

 TO ACQUIRE A RETURN OR REPAIR 

AUTHORIZATION NUMBER YOU MUST GO THROUGH THE WARRANTY PROCESS: E-mail Photos of damaged 
parts to: 

[email protected]

 or mail to: Awntech Corporation, 10950 S. Pipeline Rd., Bldg 1, Euless, TX 76040

 

 
Authorized returns should be shipped to:  

Returns Department

: Awntech Corporation, 10950 S. Pipeline Rd., Bldg 1, Euless, TX 76040 

 

Содержание Houstonian






















Отзывы: