Award MI930 Скачать руководство пользователя страница 39

Страница: 39 / 60

BIOS SETUP

MI930 User’s Manual

Power Management Setup

Phoenix - AwardBIOS CMOS Setup Utility

Power Management Setup

ACPI Suspend Type

S1(POS) ITEM

HELP

C2 Disable/Enable

Disabled

Power Management Option

User Define

Menu Level >

HDD Power Down

Disabled

Video Off Option

Suspend

Off

Video Off Method

V/H SYNC+ Blank

Modem Use IRQ

Soft-Off by PWR-BTTN

Instant-Off

PowerOn by PCI Card

Disabled

Modem Ring Resume

Disabled

ACPI XSDT Table

Disabled

HPET Support

Enabled

RTC Alarm Resume

Disabled

Date (of Month)

Resume Time Alarm (hh:mm:ss)

0 : 0 : 0

ACPI Suspend Type

The default setting of the ACPI Suspend mode is

S1(POS)

Power Management Option

This field allows you to select the type of power saving management
modes. There are four selections for Power Management.

Min. Power Saving

Minimum power management

Max. Power Saving

Maximum power management.

User Define

Each of the ranges is from 1 min. to

1hr. Except for HDD Power Down
which ranges from 1 min. to 15 min.

HDD Power Down

When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.

Video Off Method

This field defines the Video Off features. There are three options.

V/H SYNC + Blank

Default setting, blank the screen and turn
off vertical and horizontal scanning.

DPMS

Allows BIOS to control the video display.

Blank Screen

Writes blanks to the video buffer.

Modem Use IRQ

This field sets the IRQ used by the Modem. By default, the setting is

Содержание MI930





























































Результаты поиска

Содержание MI930

Отзывы:

Похожие инструкции для MI930

Бренды по названию

Популярные бренды

Award MI930, Руководство пользователя

Результаты поиска

Содержание MI930

Отзывы:

Похожие инструкции для MI930

Бренды по названию

Популярные бренды