manualshive.com logo in svg

Award MI800, Руководство пользователя, Страница: 27 / 66

Поделиться
Скачать
Award MI800 Скачать руководство пользователя страница 27

BIOS SETUP 

                         MI800 User’s Manual 

23 

BIOS Setup 

 

This chapter describes the different settings available in the Award 
BIOS that comes with the board. The topics covered in this chapter are 
as follows: 

 

BIOS Introduction ........................................................................ 24 
BIOS Setup ................................................................................... 24 
Standard CMOS Setup ................................................................. 26 
Advanced BIOS Features ............................................................. 29 
Advanced Chipset Features .......................................................... 32 
Integrated Peripherals ................................................................... 34 
Power Management Setup ............................................................ 38 
PNP/PCI Configurations .............................................................. 41 
PC Health Status ........................................................................... 42 
Frequency/Voltage Control .......................................................... 43 
Load Fail-Safe Defaults ................................................................ 44 
Load Optimized Defaults ............................................................. 44 
Set Supervisor/User Password ...................................................... 44 
Save & Exit Setup ........................................................................ 44 
Exit Without Saving ..................................................................... 44 

Содержание MI800



































































Отзывы:

Нет отзывов