background image

Quick start guide

Model: VCS702-WM

ErisStation 

businessphones.v tech.com

Conference Phone  
with Two Wireless Mics

Congratulations

on purchasing your new VTech product.
For support, shopping, and everything new at VTech, visit 
our website at 

http://businessphones.vtech.com

 or call 

(US) 

1-800-595-9511

, (Canada) 

1-800-267-7377

.

Install battery to the wireless mic

Risk of explosion! Batteries should not be exposed to 
excessive heat such as bright sunshine or fire.
Use only the supplied battery.
Risque d’explosion! Le bloc-piles ne doit pas être exposé à 
la chaleur excessive telle que la lumière du soleil ou au feu.
N’utilisez que la pile incluse.


1.  Plug the battery connector securely into the socket inside

Plug the battery connector securely into the socket inside 
the battery compartment. Insert the battery with the label  

THIS SIDE UP

 facing up onto the battery compartment.

2.  Slide the battery door until it clicks into place.

3.  Place the wireless mics into the charging cradles until 

they are flush.

Register the wireless mic

You should register your new wireless mic to the base unit 

following the instructions below.

To register the wireless mic

As part of this process, all existing, broken, or lost wireless 

mics will be deregistered first. Then, the base unit will 

re-register the two wireless mics that are placed into the 

charging cradles.
Before registration, unplug the telephone line cord from the 

wall jack to make sure there are no incoming calls during 

registration.

Gather the two wireless mics that are to be registered, 

and then place them into the charging cradles.
Enter 

331734

 on the base unit when it is not in use, 

and then press

 

. The screen displays 

Please place all 

wireless mics

 

on cradle, then press ‘SELECT’

.

Make sure both wireless mics are on the charging 
cradles, and then press

 

. The wireless mics enter the 

deregistration mode, and the screen displays 

Processing...

.

After deregistration is complete, registration starts. 

The screen displays 

Registering... 1 2

. The number 

X

 

blinks while registering the X-th wireless mic. You hear a 

confirmation tone when each wireless mic is registered. 

When both wireless mics are registered, the base unit 

displays 

Registration done

.

1.

2.

3.

Charge the battery for 8 hours before use.
If the wireless mic unit becomes warm when the 
battery is charging, it is normal.


After registration, plug the telephone line cord back into the 

wall jack.

If registration fails, the base unit will display 

Registration failed. Try again

 and 

returns to idle. You hear an error tone. Remove 

the wireless mics from the charging cradles and 

place them back in. Repeat steps 1 to 3 to try 

the entire registration process again.
If the screen does not display 

Registration 

done

 after step 3, repeat steps 1 to 3 to try the 

entire registration process again.
All wireless mics should always be kept on the 

charging cradles during the whole registration 

process. Any wireless mic that is registered 

before but not put into the charging cradle will be 

deregistered after the above operations.
Status indicators on the wireless mics flash red 

and green alternately during registration.
To cancel registration, press 

. The base unit 

displays 

Registration cancelled

. If registration 

is cancelled, some of the wireless mics may 

be deregistered. To register them back to the 

base unit, repeat steps 1 to 3 to try the entire 

registration process again.

Specifications are subject to change without notice.
© 2015 for VTech Communications, Inc.
All rights reserved. 06/15. VCS702-WM_QSG_V1.0 
Document order number: 96-010673-010-100

3

Отзывы: