Avtech AVMH-1A-C Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 29

Avtech AVMH-1A-C Скачать руководство пользователя страница 17

REAR PANEL CONTROLS

1. AC POWER INPUT. An IEC-320 C14 three-pronged recessed male socket is

provided on the back panel for AC power connection to the instrument. One end of
the detachable power cord that is supplied with the instrument plugs into this
socket.

2. AC FUSE DRAWER. The two fuses that protect the AC input are located in this

drawer. Please see the “FUSES” section of this manual for more information.

3. DC FUSES. These two fuses protect the internal DC power supplies. Please see the

“FUSES” sections of this manual for more information.

4. OS INPUT CONNECTOR. (Present on units with -OS option only.) A DC offset in the

range of ±50V (250 mA max) may be applied to this solder terminal. The DC offset
will appear on the output. When this feature is not used, the OS input should be
connected to ground (using the adjacent GND connector). This is especially
important when driving loads containing a diode.

5. GND CONNECTOR. This solder terminal is connected to ground. It may be used to

ground the OS input connector.

6. M OUTPUT CONNECTOR. (Present on units with -M option only.) This SMA

connector output provides a 20 dB attenuated coincident replica of main output, for
monitoring purposes.

17

2

3

1

4

5

6

OS

GND

M

«
...
15
16
17
18
19
...
»

Содержание AVMH-1A-C






























Отзывы:

Нет отзывов