manualshive.com logo in svg

Avtech AVIR-2-B, Инструкция по эксплуатации

Поделиться
Скачать
Avtech AVIR-2-B Скачать руководство пользователя страница 18

REAR PANEL CONTROLS

1. AC POWER INPUT. An IEC-320 C14 three-pronged recessed male socket is 

provided on the back panel for AC power connection to the instrument. One end of 
the detachable power cord that is supplied with the instrument plugs into this 
socket.

2. AC FUSE DRAWER. The two fuses that protect the AC input are located in this 

drawer. Please see the “FUSES” section of this manual for more information.

3. DC FUSES. These two fuses protect the internal DC power supplies. Please see the

“FUSES” sections of this manual for more information.

4. GATE. This TTL-level (0 and +5V) logic input can be used to gate the triggering of 

the instrument. This input can be either active high or active low, depending on the 
front panel settings or programming commands. (The instrument triggers normally 
when this input is unconnected). When set to active high mode, this input is pulled-
down to ground by a 1 kΩ resistor. When set to active low mode, this input is pulled-
up to +5V by a 1 kΩ resistor.

5. TRIG. This TTL-level (0 and +5V) logic input can be used to trigger the instrument, if

the instrument is set to triggering externally. The instrument triggers on the rising 
edge of this input. The input impedance of this input is 1 kΩ. (Depending on the 
length of cable attached to this input, and the source driving it, it may be desirable 
to add a coaxial 50 Ohm terminator to this input to provide a proper transmission 
line termination. The Pasternack (www.pasternack.com) PE6008-50 BNC feed-thru 
50 Ohm terminator is suggested for this purpose.)

6. GPIB Connector. A standard GPIB cable can be attached to this connector to allow 

the instrument to be computer-controlled. See the “Programming Manual for -B 
Instruments” for more details on GPIB control.

GATE

TRIG

AMP/PW

RS-232

GPIB

MON

OS

GND

18

2

3

6

1

4

5

8

9

7

10

11

Содержание AVIR-2-B














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды