IMPORTANT!
For safety reasons, the concrete wall must be
capable of supporting the combined weight of the mount
and the display. The manufacturer takes no responsibility for
failure caused by walls of insufficient strength.
(C)
Concrete Anchor (x4)
INSTRUCTION MANUAL
Model:
AFM600B
Display Size:
37” to 65”
Maximum Load:
45 kg (100 lbs)
Mounting Pattern:
600 mm x 400 mm (23.6” x 15.7”) max
Tilt Range:
up to 10° down
Pan/Swivel Range:
up to 180°
Profile:
3.8 cm to 42.5 cm (1.5” to 16.7”)
PRODUCT CARE:
Periodically clean your mount with a dry
cloth. Inspect all screws and hardware at regular intervals
to ensure that no connections have become loose over
time. Re-tighten as needed.
CAUTION:
Do not use this product for any purpose not
explicitly specified by AVS. Improper installation may cause
property damage or personal injury. If you do not
understand these directions, or have doubts about the
safety of the installation, contact AVS Customer Service or
call a qualified contractor. AVS is not responsible for damage
or injury caused by incorrect mounting, assembly, or use.
WARNING!
This product contains small items that could
be a choking hazard if swallowed. Keep these items away
from young children!
The wall or mounting surface must be capable of
supporting the combined weight of the mount and the
display; if not, the structure must be reinforced.
Locate pipes, wires, or any other hazards in the wall where
you wish to install.
1
Follow all instructions and recommendations regarding
adequate ventilation and suitable locations for mounting
your display. Consult the owner’s manual for your
particular display for more information.
AV Supply Group (AVS) intend to make this manual
accurate and complete. However, AVS makes no claim that
the information contained herein covers all details,
conditions, or variations. Nor does it provide for every
possible contingency in connection with the installation or
use of this product. The information contained in this
document is subject to change without notice or
obligation of any kind. AVS makes no representation of
warranty, expressed or implied, regarding the information
contained herein. AVS assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.
7
8
2
3
4
5
(A)
M8 x 63 Lag Bolt (x4)
(B)
Lag Bolt Washer (x4)
(D)
M6 x 12 Screw (x4)
(K)
S4 Allen Key (x1)
(L) S8 Socket Wrench (x1)
(E)
M6 x 30 Screw (x4)
(G)
M8 x 30 Screw (x4)
IMPORTANT!
For safety reasons, this mount must be secured
to at least two wood studs no less than 16” apart. The studs
must be capable of supporting the combined weight of the
mount and display.
Part 1A – Mounting to the Wall (Drywall)
3
4
5
6
SPECIFICATIONS
BOX CONTENTS
HARDWARE KIT
TOOLS REQUIRED
INSTALLATION
IMPORTANT SAFETY INSTRUCTIONS
(F)
M8 x 12 Screw (x4)
Phillips Head Screw Driver
Ratchet or Driver with 13 mm (1/2”) Socket
Electric or Portable Drill
6 mm (1/4”) Drill Bit and Stud Finder for Drywall Installation
10 mm (3/8”) Masonry Bit for Concrete Installation
Mount (x1)
Mount Arm (x2)
Instruction Manual (x1)
Hardware Kit (x1)
Part 1B – Mounting to the Wall (Concrete)
(H) M6 Washer (x4)
Fig. 2
Fig. 3
Use a high quality stud finder to locate a stud where you
wish to install your mount. Mark both edges of the stud to
help identify the exact center.
NOTE:
You must use the center of
the stud to avoid cracking or
splitting the wood during
installation.
Carefully remove the plastic
covers from the mount as shown
(see Fig. 1).
Place the mount against the wall
and level it using the integrated
bubble level.
While another person holds the
mount in position, mark four
locations (two per stud) for
securing the mount to the wall
(see Fig. 2).
Set the mount aside and drill a 6
mm (1/4”) pilot hole at each
marked location.
Place the mount against the wall
over the drilled holes, making
sure the arrow on the mount
points up. Attach the mount to
the wall using the lag bolts (A) and lag bolt washers (B)
provided (see Fig. 3).
Do not over-tighten these bolts and
do not release the mount until all bolts are in place.
Ensure that the mount remains level after all bolts are
secured.
1
2
6
Safety gear and proper tools must be used. Failure to do so
can result in injury or damage.
FULL-MOTION WALL MOUNT
fits most flat panel TVs
(I) M8 Washer (x4)
(J) Spacer (x8)
Fig. 1
Thank you for choosing the AVS AFM600B. Before beginning installation, please
check all parts are included and undamaged. For any parts enquiries, please
contact AV Supply Group Ltd on (09) 274 9172 or email to [email protected]
