Connect to Power Source
Connect the
The wall
outlet must be located near the product and be easily
accessible.
Helpful hints:
To avoid damage the set, use only the
adaptor supplied!
The type plate is located on the back of the set.
Replacing Backup Batteries on Unit
Install/Replace Backup Battery
These set uses a backup battery system to provide
continuous alarm operation and clock settings in the
event of a power failure. If the clock or alarm not work, it
is time to replace the backup batteries. Please make sure
the AC adaptor is connected, otherwise all settings may
be lost during battery replacement.
Open the battery compartment cover located on the
bottom of the unit. Insert 2 “AAA” size batteries as
indicated. We recommend the use of alkaline
batteries for longer life.
Batteries information:
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
Install/Replace the Remote Control Batteries
The remote control batteries are already installed at the
factory. Remove battery insulator tape before use. When the
remote control stops operating or its range seems reduced,
replace the batteries with new ones.
1. The battery door is located on the back of the unit.
2. Pull the battery door out.
3. Insert one “CR2032” 3-volt lithium batteries. Make sure
the polarity (the + and - side of the battery) is correct.
4. Fully insert the battery door back to the original position.
NOTE:
mains adaptor
DC 9V
into DC IN Jack
and the other end into the wall socket.
Battery contain chemical substances, so they
should be disposed of properly.
Power Supply
Switching on the system
1. Press
and the LCD display is on with backlighting. (The system will
switch to the last selected source.)
2. Press
MODE
to select function mode (RADIO/IPOD/USB/CARD/AUX).
Switching the system to standby mode
In any source mode, press
.
Switching off the volume temporarily
Press
MUTE
on the remote control to stop sound playback instantly.
Playback will continues without sound and the display shows MUTE.
To start sound playback, press
MUTE
again, adjust the volume controls or change source.
Setting the Clock
1. Press and hold
MEMORY/SET
to select 12 Hours/24 Hours mode.
2. Press
MEMORY/SET
once, then
clock digits for hours flashes. Press
SKIP+/-
repeatedly to set and
adjust the hours.
3. Press
MEMORY/SET
once, then clock digits for minutes flashes. Press
SKIP+/-
repeatedly to set and
adjust the minutes.
4. Press
MEMORY/SET
to confirm.
Using the Alarms
General
Two different alarm times can be set. This can be useful when you need to be woken up at a different time
e.g. During the week and at the weekend, and you can set different wake-up modes:
BUZZER→RADIO→IPOD→USB→CARD
Setting the Alarms
1. In any mode, press hold
ALARM 1
or
ALARM 2
for two seconds. (
ALARM 1 / ALARM 2
icon and the hour
digits flash
.
)
2. Hold down or press
SKIP+/SKIP-
repeatedly to set and adjust the hours.
3. Press
ALARM 1 / ALARM 2
to confirm. (
ALARM 1 / ALARM 2
icon and the minutes digits flash.)
4. Hold down or press
SKIP+/SKIP-
repeatedly to set and adjust the minutes.
5. Press
ALARM 1 / ALARM 2
to confirm
and then select your choice of alarm mode:
BUZZER→RADIO→
IPOD→USB→CARD
6.
Press
ALARM 1 / ALARM 2
to confirm.
7. At the set alarm time, the BUZZER, RADIO, IPOD, USB or CARD will switch on automatically.
Arming and Disarming Alarm (Turn Alarm ON/OFF)
Slide up
ALARM ON/OFF
button to arm or disarm functions. When armed, the related alarm icon
appears in display.
Resetting the Alarm to Come on the Next Day
When the alarm is sounding, slide up
ALARM ON/OFF
button to stop alarm and reset it to come on the
following day.
Snooze
Press the
SNOOZE
button after the alarm sounds. The alarm will be silenced and come on again 9
minutes later. Snooze can be pressed several time during 1 hour alarm cycle.
Helpful hints:
If you have selected RADIO alarm mode, make sure you have properly tuned to a station before tuning
off the set.
If you have selected IPOD alarm mode, make sure you have docked the compatible player.
If you have selected USB or CARD mode, make sure you have inserted USB or CARD into related jack
before tuning off the set.
To check the alarm time setting for ALARM 1 or ALARM 2, press ALARM 1 or ALARM 2 button.
POWER ON/OFF
for 2 seconds
POWER ON/OFF
Basic Operation
ENG-5
ENG-4
DC
IN
Battery door
