AVL 9120 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 114

background image

This Operator´s Manual contains important warnings and safety information to be observed by the
user.

This instrument is only intended for one area of application which is described in the instruc-
tions. The most important prerequisites for application, operation and safety, are explained to
ensure smooth operation. No warranty or liability claims will be covered if the instrument is
applied in areas other than those described or if the necessary prerequisites and safety
measures are not observed.

The instrument is only to be operated by qualified personnel capable of observing these
prerequisites.

Only accessories and supplies either delivered by or approved by AVL are to be used with the
instrument.

Due to the operating principle of the instrument, analytical accuracy not only depends on
correct operation and function, but also upon a variety of external influences beyond the
manufacturers control. Therefore, the test results from this instrument must be carefully
examined by an expert, before further measures are taken based on the analytical results.

Instrument adjustment and maintenance with removed covers and connected power mains are
only to be performed by a qualified technician who is aware of the dangers involved.

Instrument repairs are only to be performed by the manufacturer or qualified service personnel.

Symbol

Explanation

Attention symbol - Refer to the Operator's Manual or Service
Manual for further instructions. This symbol is located on the
inside of the instrument.

Type B instrument symbol - An instrument of the B type falls under
safety categories I, II, or III, or has an internal power supply providing
the required insulation against discharge current and reliable ground
connections.

Important Information!

iii

Important Information!

«
1
2
3
4
5
...
»

Содержание 9120



















































































































Отзывы:

Нет отзывов

Похожие инструкции для 9120

Бренд: Callaway Страницы: 13

Бренд: QMI Страницы: 54

Бренд: velocomp Страницы: 4

Бренд: Lasertec Страницы: 21

Monitoring System 500 II DC

Бренд: Didactum Страницы: 2

Бренд: Ansul Страницы: 24

Бренд: ENDA Страницы: 2

Бренд: Heinrichs Страницы: 31

Бренд: Chroma Страницы: 63

Ranger TDR VDV501-090

Бренд: Klein Tools Страницы: 44

Бренд: PRONIVO Страницы: 40

Бренд: socomec Страницы: 34

Бренд: Ratek Страницы: 25

Бренд: Camlab Страницы: 28

Бренд: Cable Ferret Страницы: 16

Бренд: Roland Страницы: 224

Бренд: ASD Страницы: 72

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды