manualshive.com logo in svg

AVL DITEST ADS 340, Руководство пользователя

Поделиться
Скачать
AVL DITEST ADS 340 Скачать руководство пользователя страница 97

 

AVL DiTEST ADS 340 

List of possible faults / troubleshooting   

 
 

User Manual 

10-3 

 

 

Device check incomplete. 
Replace refrigerant bottle. 

The device scan can not be completed due to insufficient amount 
of refrigerant. 
The refrigerant cylinder must be replaced. 

Measurement data invalid, 
calibration failed. 

If during calibration incorrect measured data calibration is 
detected aborted with this error message. 

Not enough refrigerant for 
calibration, refrigerant 
bottle must be replaced. 

The calibration can not be performed because the amount of 
refrigerant required for the calibration is not available. The 
refrigerant bottle must be replaced. 

 

Error message 

Possible cause(s), Solution 

System error 

An error indicates that the device because of a problem 
cannot be used for the time being or permanently.  
Charging indicator: red flashing quickly. 

Check pressure sensors. 

It was detected an invalid signal on one of the pressure sensors.  

All pressure sensors must be checked

.

 

Check temperature 
sensors. 

It was detected an invalid signal on one of the temperature 
sensors. All temperature sensors must be checked

.

 

Check weight sensors. 

One of the scales provides an invalid signal.  

All balances must be checked

.

 

CO

2

 concentration is above 

safety limit. Air the room. 

CO

2

 concentration is above the recommended limit.  

Make sure there is good ventilation and you leave the room until 
the CO

2

 concentration has fallen back to normal levels and the red 

flashing light goes out

.

 

CO

2

 sensor is not available.  CO

2

 sensor is not connected.  

The device cannot be used for safety reasons.  
The CO

2

 sensor must be checked. 

Pressure of refrigerant 
bottle too high. 

The pressure of the refrigerant cylinder is outside the safety limits. 
The device cannot be used until the pressure is back within the 
safety limits

.

 

System pressure too high. 

The pressure at the couplings exceed the safety limits.  
The device cannot be used until the pressure is at the couplings 
again within the safety limits

.

 

 

Error/Error messages, electrical: 

Error/Error message 

Possible cause(s) 

Solution 

Cannot be switched on

 

No power supply 

Check power supply. 
Check fuses. 

 

Error/Error messages, mechanical:

 

Error/Error message 

Possible cause(s) 

Solution 

Self-check is not starting 

No gas supply 

Connect or open supply 
Disconnect vehicle 
Close gas bottle and drain manually 

Not enough oil available 

Oil tank empty 

Fill oil bottle 

Check connection 

Vehicle not 
connected or empty 

Connect quick coupling to vehicle 

Oil filling 

– fill level not 

reached 

Oil tank empty 

Fill oil bottle 

Circuit under pressure 

 

Perform draining 

 

Содержание ADS 340

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды