Avigilon H5A Скачать руководство пользователя страница 8

EN - English - I

nstruc

tion manual

 

6

MNGQEVO_2129_EN

6 Installation

6.1 Opening the base of the 
product

To avoid scratching the product with the hexagonal 
wrench, align the groove on the body of the product 
with the screw before screwing it in (Fig. 4, page 11).
Unscrew the three screws at the bottom of the 
product (Fig. 5, page 11).

6.2 Mounting the bracket

Take special care when attaching and 
fastening down the apparatus. If the 
equipment must be fastened to a concrete 
surface, plugs must be used with a 
minimum traction force of 300dN each. For 
a metal surface use screws with a diameter 
of at least 8mm and of an appropriate 
length. The fastening system must be 
capable of supporting at least 4 times 
the weight of the entire equipment (PTZ, 
supports and adapters).

The device should be assembled vertically. 
Any other position could impair the 
performance of the device.

Various types of optional mounts and accessories are 
available.
Choose the mounting accessories for the installation 
you want to implement.
Install the optional mounts and accessories by 
following the instruction manuals provided with the 
bracket or accessory.

6.3 Cable management

The cables must be adequately fastened to 
the structure to avoid causing the cables 
to be accidentally unplugged.

You must use cables suited to the type of 
installation you are using.

Multipolar cable sheath diameter:

Cable glands M16: from 4.5mm (0.2in) up 
to 10mm (0.4in).

Cable glands M20: from 8mm (0.3in) up to 
13mm (0.5in).

Insert the cables into the cable glands (Fig. 7, page 
12).
If the cable has a pre-assembled connector, replace 
the gasket inside the cable gland with the one 
supplied. Insert the Ethernet cable in the gasket as 
illustrated in the figure (Fig. 6, page 12). Pass the 
cable with connector RJ45 through the M20 cable 
gland.
Tighten the cable glands.

Pay attention to the fixing. Tightening 
torque : 1.5Nm (±0.2Nm) for M16 cable 
glands, 2Nm (±0.2Nm) for M20 cable 
glands.

If a cable gland does not have a cable inserted, a 
specific cap must be inserted for closure. Always 
close the cable glands with the stated tightening 
torque.

6.4 Fixing the base to the support

For further details on installing the camera 
with brackets and accessories, refer to 
the manual provided with the bracket or 
accessory.

Содержание H5A



















Отзывы: