manualshive.com logo in svg

Avidyne IFD540, Руководство по установке

Поделиться
Скачать
Avidyne IFD540 Скачать руководство пользователя страница 46

 

IFD5XX Installation Manual 

600-00299-000 

Page 46 of 198 

Revision: 02 

The Approved Model List for the STC will indicate if an aircraft is required to install wire 
harness overbraid on the IFD5XX wiring. Note: Overbraid is not required on VFR only 
installations as defined in Section 2.4.1. 

4.5.3  Copper Overbraid Installation 

The copper overbraid must be a minimum 90% optical coverage per ASTM-B-33. The 
overbraid must be grounded at both ends. If the aircraft wiring passes through wire 
disconnects or bulkheads, the overbraid should be continued on each segment.   

The wire harness overbraid should also be installed per FAA AC 43.13-1B Chapter 11-189. 

4.6  IFD5XX Connectors 

The following special tools may be needed during installation of the IFD5XX: 

 

IFD5XX 

Connector 

Number 

Connector 

Part number 

Contact Part 

Numbers 

Crimp 

Tool 

Die/ 

Positioner 

Extraction 

Tool 

Insertion 

Tool 

P1001 

M24308/4- 268( ) 

M39029/58-360 

(ORG/BLU/BLK) 

M22520/02-

01 

M22520/2-09 

M81969-1-04  

M81969/1-04  

P1002 

M24308/2-3( ) 

M39029/63-368 

(ORG/BLU/GRY) 

M22520/02-

01 

M22520/2-08  M81969/1-02 

M81969/1-02  

 

P1006 

M24308/4- 266( ) 

M39029/58-360 

(ORG/BLU/BLK) 

M22520/02-

01 

M22520/2-09 

M81969-1-04  

M81969/1-04  

P1050 

M24308/4- 268( ) 

M39029/58-360 

(ORG/BLU/BLK) 

M22520/02-

01 

M22520/2-09 

M81969-1-04  

M81969/1-04  

Ground Block 

583861-7 

(TE 

Connectivity) 

5-583853-4 

(TE Connectivity) 

91535-1 

(TE 

Connectivity

) 

 

91073-1 

(TE 

Connectivity

) 

 

Table 21: D-Sub Connector Tools 

4.7  Byteflight Digital Data Bus Consideration 

– Dual IFD Installations 

Dual IFD installations use a Byteflight digital Databus protocol when connected via RS-232 
Channel 3 and configured for CrossSync. The following must be considered for replacement 
and new installations. 

4.7.1  Databus Wiring - Replacement Installations 

For installations that are replacing two previously connected GNS4xx/5xx systems, the 
Byteflight digital Databus is capable of using the pre-existing wiring between the two pre-
existing trays with no additional wiring or modifications required.  All bus termination is 
built into the IFD units. However, the existing wire length on the CrossSync connection must 
not exceed 8 feet in length on IFD5XX RS-232 Channel 3 on P1001. Installations with longer 
installation lengths between IFD5XX units must use Byteflight cable. The ByteFlight wire is 
available from Avidyne, reference Table 15. 

Содержание IFD540







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды