Avid Technology Digidesign USD Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 96

Avid Technology Digidesign USD Скачать руководство пользователя страница 7

Chapter 1: Introduction

3

USD Setup

◆

USD Setup requires its own connection

from the USD to your computer for remote
control of the USD:

Macintosh

A serial port (modem or printer,

or equivalent serial port adapter) is re-
quired for USD Setup Macintosh.
USD Setup does not work if the USD is con-
nected to a DigiSerial Port.

Windows

A COM port connection is re-

quired for USD Setup Windows. USD Setup
does not work if the USD is connected to a
DigiSerial port.

USD Standalone, without Pro Tools

If you are not using Pro Tools but using the
USD in standalone mode, no USD-to-CPU
connection is required unless you need to
do any of the following:

◆

Use the USD for Variable Speed Override

(VSO)

◆

Configure Window burn parameters

◆

Control the USD with USD Setup

If you do not connect USD to a CPU, you
will use the USD front panel to access and
edit parameters. (See “Control Options” on
page 27 for details.)

USD Standalone with Remote Control

For software remote control using the
USD Setup application, see “USD Setup”
on page 3.

USD Cables

USD Serial Cable

•A USD Serial cable is in-

cluded to connect the USD to a Macin-
tosh- or Windows-based Pro Tools
DigiSerial Port (Pro Tools MIX, MIXplus,
or Pro Tools 24 systems). This cable can
also be used to connect the USD to r a
Macintosh serial port or equivalent serial
port adaptor.

Windows

USD Setup on Windows requires

a standard 9-pin-to-25-pin modem cable to
connect the USD to a COM port on any
supported Windows computer. This cable
is available from Digidesign through your
Digidesign dealer, or from many computer
supply stores.

Compatibility Information

Digidesign can only assure compatibility
and provide support for devices it has
tested and approved.

For a list of qualified computers, diskette
drives, SCSI accelerators, serial port conver-
tors and hard drives, refer to the latest
Digidesign compatibility documents, avail-
able from Digidesign by fax or on the
Digidesign Web site.

✽

For a list of Digidesign’s contact informa-

tion, see the title page of this guide.

«
...
5
6
7
8
9
...
»

Содержание Digidesign USD

































































































Отзывы:

Нет отзывов