AVGear AVG-SC41T-CODEC Скачать руководство пользователя страница 9

Страница: 9 / 31

AVG-SC41T-CODEC

2.3. Receiver Front Panel

①

POWER LED:

The LED illuminates red when power is applied.

②

HDBT LED:

The LED illuminates green when HDBT input signal present.

③

HDMI LED:

The LED illuminates green when HDMI input signal present.

④

FIRMWARE:

Type-A USB port for updating system firmware.

2.4. Receiver Front Panel

①

HDBT IN:

Connect to the HDBT OUT port of the Transmitter via CAT5e / 6a / 7

cable. Supports PoC technology.

②

HDMI IN:

HDMI input port.

③

HDMI OUT:

HDMI output port.

④

AUDIO OUT:

Stereo balanced L/R audio output port.

⑤

DEVICES:

Two Type-A USB ports, connect with USB HID devices.

⑥

RS232:

Serial port, 3-pin phoenix connector, connect with the display device

(such as projector) needed to be control via RS232 commands.

⑦

RELAY1 & RELAY2:

Connect with relay device (such as projector screen).

⑧

LAN:

Ethernet port, works with the LAN port on the Transmitter to extend

network signal.

Note: Please notice warning label

. The LAN port can’t be connected with HDBT port.

FIRMWARE

HDBT

HDMI

1 2 3

HDBT IN

HDMI IN

HDMI OUT

AUDIO OUT

DEVICES

CONTROL

Relay1 Relay2

LAN

Содержание AVG-SC41T-CODEC
































Результаты поиска

Содержание AVG-SC41T-CODEC

Отзывы:

Похожие инструкции для AVG-SC41T-CODEC

Бренды по названию

Популярные бренды

AVGear AVG-SC41T-CODEC, Руководство пользователя

Результаты поиска

Содержание AVG-SC41T-CODEC

Отзывы:

Похожие инструкции для AVG-SC41T-CODEC

Бренды по названию

Популярные бренды