Avery Dennison M09416 TTXLI Скачать руководство пользователя страница 51

Страница: 51 / 68

M09416

Thermal Transfer Printer

7. MAINTENANCE

This session presents the clean tools and methods to maintain your printer.

1. Please use one of following material to clean the printer.

Cotton swab (

Head cleaner pen

)

Lint-free cloth

Vacuum / Blower brush

100%

ethanol

2. The cleaning process is described as following

Printer Part

Method

Interval

1. Always turn off the printer

before cleaning the print head.

2. Allow the print head to cool for

a minimum of one minute.

3. Use a cotton swab (Head

cleaner pen) and 100% ethanol

to clean the print head surface.

Clean the print head when

changing a new label roll

Print Head

Platen Roller

1. Turn the power off.

2. Rotate the platen roller and

wipe it thoroughly with 100%

ethanol and a cotton swab, or

lint-free cloth.

Clean the platen roller when

changing a new label roll

Tear Bar/Peel

Bar

Use the lint-free cloth with 100%

ethanol to wipe it.

As needed

Sensor

Compressed air or vacuum

Monthly

Содержание M09416 TTXLI



































































Результаты поиска

Содержание M09416 TTXLI

Отзывы:

Бренды по названию

Популярные бренды

Avery Dennison M09416 TTXLI, Руководство по обслуживанию

Результаты поиска

Содержание M09416 TTXLI

Отзывы:

Бренды по названию

Популярные бренды