Avdel 07572 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 20

Avdel 07572 Скачать руководство пользователя страница 9

7

C L U T C H A D J U S T M E N T

If you have ordered a complete tool the clutch will be set for the specified insert.

When purchased as a spare part, the clutch is supplied unset.

Correct clutch setting is necessary to ensure optimum deformation of the insert. If the deformation is insufficient (clutch torque too low)
the insert will rotate in the application. If the deformation is excessive (clutch torque too high) thread distortion will occur and extensive
wear on the drivescrew, may lead to fracture.

For details on how to adjust the clutch refer to maintenance instructions referring to the clutch on page 11.

Two different accessories are available to make the connection to your air supply:

A C C E S S O R I E S

Hose Connector
part nº 07005-00276

1/4” BSP

TO FIT 6.4 mm (1/4”) BORE PIPE

L = 137 cm

Hose Assembly
part nº 07008-000324

«
...
7
8
9
10
11
...
»

Содержание 07572





















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды