manualshive.com logo in svg

Avaya programming and use, Инструкция по установке и эксплуатации, Страница: 371 / 468

Поделиться
Скачать
Avaya programming and use Скачать руководство пользователя страница 371

Upgrading the System

Using a PC Card

10-5

7.

Follow the procedures below:

a.

If you are upgrading from Release 1.0 to Release 2.0, power down and remove the PC 
upgrade card.

b.

If you are upgrading to Release 3.0 or later, do not remove the PC card. The card 
automatically converts to a backup/restore and remote access card. If you removed other 
PC cards, PVM or ASA/DXD, for example, power down the system and reinstall the PC 
cards after the upgrade is complete.

8.

If you have a 2-slot carrier or a stand-alone configuration, you are finished with this procedure. 
If you have a 5-slot carrier, continue with Step 9. 

9.

Make sure all modules are seated properly.

10. If you have a 5-slot carrier and Release 4.0 or later:

a.

Position the carrier cover over the modules so that the openings on the top of the carrier 
cover align correctly with the tabs at the top of the installed 5-slot carrier and modules.

b.

Rotate the carrier cover into position so that it aligns correctly with the thumb screw 
opening on the bottom of the carrier.

c.

Tighten the thumb screw. To ensure proper alignment and safe operation, tighten the 
thumb screw securely.

If you have a system of Release 3.0 or earlier:

a.

Grasp the cover by its upper edges and hold it squarely over the control unit (see 

Figure 10-3

). Place the cover over the modules and make sure it fits firmly in place.

Figure 10-3. Replacing the Cover

b.

Tighten the screw on the lower front of the cover.

Содержание programming and use





















































































































































































































































































































































































































































































Отзывы:

Нет отзывов