manualshive.com logo in svg

Avaya M15-155, Руководство по установке, Страница: 12 / 14

Поделиться
Скачать
Avaya M15-155 Скачать руководство пользователя страница 12

Chapter 3 

Troubleshooting 

10  

M15-155 Installation Guide 

Software Download Troubleshooting 

The following are Activity Status messages that can appear during software 
download, their meanings, and suggested solutions. 

Activity Status 
message 

Description Suggested 

action 

File format unknown 

File format 
unknown 

Ensure that the correct agent software file 
is being downloaded to the agent 

File not found 

Failure of TFTP 
Get 

Type in the correct path and filename 

Server is unreachable 

or 

Server timeout 

Failed to find the 
server after 1 
minute 

Check that you typed in the correct TFTP 
Server IP address. Ensure the server is 
accessible to the agent by typing  

ip ping

 

<ip_address_of_agent>

. 

The router is defined in the IP Gateway 
menu. 

To many Boot Images 
in Flash 

 

Erase one of the Boot Images from Flash 
memory 

To many Main Images 
in Flash 

 

Erase one of the Software Version from 
Flash memory 

Access Violation 

You do not have 
the required 
access permission 

You must obtain the required access 
permission 

 

Содержание M15-155















Отзывы:

Нет отзывов