Avaya J100 Series Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 528

Avaya J100 Series Скачать руководство пользователя страница 78

Chapter 6: Phone configuration

Avaya J100 Series IP Phones can be configured by using one of the following methods:

• the Administration menu on the phone
• the web interface of the phone Administration menu
•

46xxsettings.txt

file

Related links

Configuring the phone using Administration menu

Configuring the phone using the web interface

on page 94

Configuring the phone using the settings file

Configuring the phone using Administration menu

The Administration menu can be accessed from the Main Menu of the phone. For more

information about accessing the Administration menu, see

Accessing the Admin menu after log

on page 79.

The Administration menu contains the following sections:

• IP Configuration
• Debug
• Network interfaces
• Group
• Get Updates
• Log
• Log out
• Ping
• Reset to defaults
• Restart phone
• SIP
• SSON
• View

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

78

Comments on this document? [email protected]

«
...
76
77
78
79
80
...
»

Содержание J100 Series

















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов