Avaya ERS 8600 series Скачать руководство пользователя

Страница: 374 / 420

config vlan 10 ports add 3/1

3. Assign an IPv6 address to the to the VLAN by using the following command:

config vlan 10 ipv6 create addr 4000::1/120

4. Enable the new VLAN by using the following command:

config vlan 10 ipv6 admin enable

Creating an IPv4 brouter port on the source device

Procedure steps

1. Create a brouter port with an IPv4 address by using the following command:

config ethernet 3/30 ip create 172.21.80.1/24 1000

2. Enable OSPF on the port by using the following command:

config ethernet 3/30 ip ospf enable

3. Enable OSPF on the device by using the following command:

config ip ospf enable

Creating an IPv6 VLAN with ports on the remote device

Configure the IPv6 VLAN with ports (VLAN 40 in the figure) on the destination device, or 8600.

Procedure steps

1. Create a VLAN by using the following command:

config vlan 40 create byport 1

2. Add ports to the VLAN by using the following command:

config vlan 40 ports add 3/2

3. Assign an IPv6 address to the to the VLAN by using the following command:

config vlan 40 ipv6 create addr 4000::2/120

4. Enable the new VLAN by using the following command:

config vlan 40 ipv6 admin enable

Creating an IPv4 brouter port on the destination device

Create an IPv4 brouter port on the destination device.

IPv6 CLI configuration

374 Configuration — IPv6 Routing

November 2010

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды