Avaya ERS 8600 series Скачать руководство пользователя

Страница: 298 / 420

Variable

Value

ports

Specifies a port/slot or a port list.

Configuring MLD on a brouter port

Configure MLD on a brouter port to customize the configuration.

Procedure steps

Configure MLD by using the following command:

config ethernet

<ports>

ipv6 mld

Variable definitions

Use the data in the following table to use the

config ethernet ipv6 mld

command.

Variable

Value

info

Displays the current brouter port MLD configuration
setting.

last-memb-query-int

<seconds>

Configures the query interval time in 1/10 of a second
for the last member.

seconds

is in the range 0–65535.

ports

Specifies a port/slot or a port list.

query-interval

<seconds>

Configures the query interval time in 1/10 of a second.

seconds

is in the range 0–65535.

query-maxresp

<1seconds>

The maximum query response time advertised in MLD
queries on this interface.

seconds

is in the range 0–65535.

robustval

<integer>

Configures the robustness value.

integer

is in the range 0–65535.

version <1|2>

Configures the version of MLD to version 1 or version
2.

Multicast protocol configuration using the CLI

298 Configuration — IPv6 Routing

November 2010

Содержание ERS 8600 series





































































































































































































































































































































































































































Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды

Avaya ERS 8600 series, Руководство по настройке

Результаты поиска

Содержание ERS 8600 series

Отзывы:

Похожие инструкции для ERS 8600 series

Бренды по названию

Популярные бренды