Avaya ERS 8600 series Скачать руководство пользователя | Manualshive

Страница: 27 / 420

background image

Router discovery

IPv6 nodes discover routers on the local link with router discovery. The IPv6 router discovery

process uses the following messages:

•

Router advertisement

on page 27

•

Router solicitation

Router advertisement

Configured interfaces on an IPv6 router send out router-advertisement messages. Router-
advertisements are also sent in response to router-solicitation messages from IPv6 nodes on
the link.

Router solicitation

An IPv6 host without a configured unicast address sends router solicitation messages.

Multicast

Most of the IPv6 routing protocols use multicast addresses for sending some of the protocol
information, especially during the discovery phase. To receive these messages the device
registers the well-known multicast addresses when a particular protocol is enabled and
deregisters when the protocol is disabled.

As in IPv4, a multicast address is assigned to a set of interfaces belonging to different nodes. A
packet destined to a multicast address is routed to all interfaces identified by that address. The
IPv6 multicast address uses the FF00::/8 prefix which is equivalent to the Ethernet multicast
address of 33-33-.

Multicast neighbor solicitation exists for address resolution, duplicate address detection, and
multicast router solicitation and router advertisement

IPv6 and the Avaya Ethernet Routing Switch 8800/8600

IPv6 routing provides an underlying mechanism to transmit data blocks from source to
destination. The source and destination are hosts, identified by fixed-length IPv6 addresses.

The Transmission Control Protocol (TCP) and User Datagram Protocol (UDP) provide a
transport facility for data transmission. TCP is a reliable mechanism. UDP is not as reliable as
TCP. Routing protocols identify the shortest path from a source to a destination. The Internet

IPv6 and the Avaya Ethernet Routing Switch 8800/8600

Configuration — IPv6 Routing

November 2010 27

«
...
25
26
27
28
29
...
»

Содержание ERS 8600 series





































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERS 8600 series

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

Бренд: CAME Страницы: 19

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 32

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

SMART NODE 4950-NCE

Бренд: Patton electronics Страницы: 8

NetLink 2960 RAS

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 2

Бренд: Qlogic Страницы: 20

Бренд: Amperes Страницы: 8

ER3-100 (5K02-55)

Бренд: 8e6 Technologies Страницы: 74

Бренд: Abocom Страницы: 1

DM/IP601-CPCI-100BT

Бренд: Dialogic Страницы: 2

Бренд: Edgewater Networks Страницы: 7

SmartSwitch 8-slot

Бренд: Cabletron Systems Страницы: 150

ADSL2+ Wireless MIMO Router

Бренд: Ace Страницы: 64

Бренд: Tripp Lite Страницы: 3

Бренд: Digital Equipment Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды